Draw shear and moment diagram for the following frame: by Method Coherent deformations. (q1=4,0K , q2=6.0K), (P1=10K , p2=20K) (L1=30 ft , L2=55FT L3=40FT ) (q1 + q2) L1/3 P1 L1/3

Q: FIGURE 1. 40 kN 40 kN/m A B 20 kN/m E ए 2 m 1m 4 m 2 m R, R2 What is the maximum intensity of moment…

A: Draw SFD and BMD and answer the questions

Q: R20

A:

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: E A F D 3 in. in. G -2 in. 1.5 in B

A:

Q: Compute the total length of 10 mm diameter stirrups for a beam section 500 mm x 250 mm. Total length…

A:

Q: 100 mm 150 mm

A:

Q: QUESTION 5 Which of the following represents the location of the horizontal plastic neutral axis (X,…

A: Solution Find the location of horizontal plastic neutral axis

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: Find the centroid, ^y, and moment of inertia Ixx of the following sections.

A: The moment of inertia about X-Xaxis can be found using parallel axis theorem, IXX=IGG+A×h2IGG=MOI…

Q: Now please solve 7-10

A: Some statements regarding highway and traffic engineering

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: 16. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A:

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: 1. Find the shortest path from A to D. B 2 3. 2 G 5 F8E

A:

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

A:

Q: Breaks the selected object .between two points You can create arc or line between two specified…

A: Given- Breaks the selected object .between two points   a) You can create arc or line between two…

Q: 80 mm -L- В D 60 mm

A:

Q: There are support reactions Ay and By which both equal 3.5kN going upwards.

A:

Q: D A E Given side B G Assuming that all stations are occupied and al lines are observed, what is the…

A:

Q: answer this too please y bar put 3 demicals if possible

A: Centroid y = (A1y1-A2y2)/ (A1-A2)

Q: CORRECT ANSWER

A:

Q: 10 GN/m² to kip/inch²

A: Given unit is GN/m2 1GN=224808.94kip And 1m=39.37inch

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: 1. Ah = [ Select ] 2. Av [ Select ] 3. MA = [ Select ] %3D 4. C, = [Select ] 5. Dy = [ [ Select ] 50…

A:

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: What is the distance between the kerns for the section given below? K- 100- 50 200 50 50

A:

Q: ] Use graph paper to draw simplified sketch of the gear and the rack shown in problem 5/64(79). What…

A: Figure is as shown

Q: Find shape factor Q about the y-axis.

A:

Q: *9-64. Locate the centroid (, y) of the shaded area. y 1 in. 3 in 3 in. 3 in. Prob. 9-64 Ai=…

A:

Q: Identify the centroid of the 1/4 circle projected whose radius is r. Utilize integration. Yo -x Хо

A:

Q: Which among the following determines the direction of closing error? a. Tan δ = ΣD/Σ O_b. c. d. Tan…

A:

Q: Halp me to out

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.