Draw a neat, labelled layout  and ighlight the necessary support services required for  functioning for the-Cardiology  departments:

Q: tiate between focus and epicenter

A: solution of above problem is below:

Q: An 80m spiral curve with a 6 degree circular curve connects two tangents having azimuths of 240deg…

A: This question is related to the Spiral Curve from Surveying Engineering. In this question we…

Q: na certain road construction, it was decided to connect a forward tangent of 3% and a back tangent…

A: Given:- forward tangent=3% back tangent=-5% 200m-symmetrical parabolic curve grade intersection at…

Q: a. Differentiate between following term:- a)Base line and a check line b) Main station and Tie…

A: Since we answer one question at a time so we will answer the first one. Please resubmit the another…

Q: 1- The disk is moving to the left such that it has an angular acceleration a = 8 rad/s and angular…

A:

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A: E = 12 GPa Use virtual method to analyze the beam.

Q: Water flows through a horizontal branching pipe as shown at a rate of 280L/s. All points are inside…

A: P1=70kPa Q=280L/s A1=0.1m2 V3=6m/s To find pressure at section 3

Q: 300 lb In the truss loaded and supported as shown, the following using the Method of Joints : 300,…

A:

Q: From the given frame shown. Which of the following is the vertical reaction at D? if q =18 kN, and L…

A: Given                     q = 18 kN/mL = 10 m

Q: Suppose your taping party was tasked to layout a line perpendicular to AB (see Figure 1). Discuss…

A: Given data in question  Line AB Tape is the only instrument  To find out  How to make perpendicular…

Q: 3 4.20 B A 4.0 m BAR WEIGHING 100 N IS REUTING ON A SMOOTH FLOOR AND AGAINST A MOOTH WALL AT POINTr…

A: To find the value of P

Q: 1. Determine the location of centroid, y, from top of the beam in mm. 2. Determine the moment of…

A: Answer (1) Calculation of location of centroid Consider 2 C section as one single I section as shown…

Q: Current Attempt in Progress (Bernoulli/continuity) Water flows steadily through a diverging tube as…

A: Given:in fig Diverging tube  d3=1.03ft  d2 =0.74  d1=0.52ft Specific gravity of manometric tube…

Q: Q- An orifice is located at side of tank with water level is 1.5 m above the centre of orifice.…

A: Water level y=1.5 m, Distance x=0.8 m, Vertical fall h=0.2 m,

Q: C If after many years of operation at Re = 105, the pipe's inner surface becomes rough with an…

A: Given, Re = 105  Roughness height, ε = 0.2 mm    NOTE : From recommended matches,     Velocity when…

Q: 10.73 An engineer is making an estimate of hydroelectric power for a home owner. This owner has a…

A:

Q: one-way slab to support a load

A: To design the slab for the given specifications

Q: Problem 1a. Determine whether each of the beams and frames below are internally determinate,…

A: No. of reaction = (3 for fixed 2 for hinge 1 for roller)  a.)No. of Reaction = 4 (2+1+1) (2 for…

Q: Q.8.8 P The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. What is…

A:

Q: PART I. CRITICAL PATH METHOD From the given Activities and their Durations below, create a Critical…

A: The critical path method (CPM) is a technique where you identify tasks that are necessary for…

Q: The installation cost of a machine is $8000 with estimated life of 10 years and selvage value of…

A: For the straight line method the depreciation is constant for every yearDepreciation per…

Q: A steel pipe pile of 61 cm outside diameter with a wall thickness of 2.5 cm is driven into loose…

A:

Q: 0.8 m 643m 15 AN C LOM D VN 120

A: Given Data:UDL=6kN/mConcentrated Load = 15kNSpan =3m

Q: 1. You are hauling soil from a borrow pit, up hill, to a fill site. Determine the following, using…

A: Work done per cycle is denoted by W ;weight of soil being moved is given by ;Density of clay loam =…

Q: For an undisturbed sample: given that Void ratio = 0.78 Water content 12% Specific gravity of solids…

A: Given: The void ratio is 0.78. The water content is 12%. The specific gravity of solids is 2.68.

Q: Q.2- A 10-mm- diameter Brincll hardness indenter produced an indentation 2.50mm in diameter in a…

A:

Q: Problem #2: Note: Replace all zero digits of your ID number by number "2" e = 40 + C (degrees) 650 +…

A:

Q: Find the total area

A: Consider the figure,

Q: Problem 1. A transit with an external focusing telescope has a stadia interval factor of 100.8 was…

A:

Q: A fillet weld of size 6mm used to weld a plate of width 75mm to gusset plate to transfer a factored…

A: Size of weld=6 mm,Width of plate=75 mmFactored load=120 kN,Site weld case, Fe410 steel,Welding is…

Q: 7. The beam has the following data: fy = 275 MPa, fc' = 30 MPa, base = 360 mm, effective depth = 450…

A:

Q: A 24-hr storm occurred over a catchment of 2.8 km area and the total rainfall observed was 10 cm. An…

A:

Q: Given the cantilever beam with point loads, find the magnitude of the vertical reaction at A.…

A: The required FBD can be drawn as below ;Consider all forces and reactions acting on each point of…

Q: Statically undetermined system and its bending moment diagram for elastic case are given in the…

A:

Q: Draw the shear and moment diagrams for the double overhanging beam. 400 lb 400 lb 200 lb/ft В 3 ft 6…

A: Given,

Layout and Design

The layout is the process of marking all the building components on the land from the prepared plan. The layout of construction includes transferring the whole plan of foundations, boundaries of the structure, centerline of the wall, and all other important structural parts on the ground along with the length and width so that the components of buildings can be excavated properly. Designing is the process of establishing the concept of the building on paper in a properly engineered manner.