distortion is specified not to exceed 1.5% of the peak-to-peak analog signal. Q17/ The information in an analog waveform, with maximum frequency fm=1 KHz, is to be transmitted over M level PCM system, where number of pulse level M=64. The quantization ever M level PCM system, where number of pulse level M=64. The quantization this PCM system. AWhat is the minimum required sampling rate, and what is the resulting bit transmission rate. (6) What is the PCM pulse or symbol transmission rate?

Q: Flat top sampling is obtaining by multiplier analog signal by pulse signal True False

A: This statement is True as flat top sampling is obtaining by multiplier analog signal by pulse…

Q: 3. Analyse the modulation diagram given below and develop the equations of the modulated signals for…

A: Answer:

Q: Using step function u(t), plot the following signals in one figure. Consider the time range…

A: HERE IS YOUR CODE IN MATLAB INPUT CODE

Q: 8-PCM system is used to encode 15 kHz audio signal using 64 levels. The bit rate is -------- and…

A: EXPLANATION Below is the answer for the given question. Hope you understand it well. If you have any…

Q: Write synthesizable VHDL code for a 5-to-10 decoder with an enable signal, active low, and outputs…

A: kindly check step 2 for code

Q: The difference in the delay of the signal may create a difference in  Phase explain?

A: Given that: The difference in the delay of the signal may create a difference in  Phase explanation?

Q: b) The sinusoidal test signal 5cos(12566t) is applied to a delta modulator with sampling frequency =…

A: Step Size for Minimizing Slope Overload Quantization Error:Slope overload distortion occurs when the…

Q: b-For a PCM system the number of bits that represents each sample is 5bits and the bandwidth is 0.75…

A: Given : Number of bits = 5  Bandwidth = 0.75 * Maximum Bandwidth Bandwidth = 45Khz Erfc = 0.001

Q: Draw the waveform for the data 100100110 using the following encoding schemes: (i) Unipolar NRZ (ii)…

A: Given data is 100100110: i) Unipolar NRZ In unipolar NRZ, Positive Voltage defines bit 1 and zero…

Q: Assume Io, I1, I2 and I3 in the following truth table are the Data Inputs of a 4:1 MUX. Take A and C…

A: MULTIPLEXER: The Multiplexer is a combined circuit with a maximum of 2n data inputs, 'n' line…

Q: Given the following timing waveform for Y, draw D and E. 10ns Sns 10ns 2ns 10 20 30 wire #3 D; //…

A:

Q: A 12-bit analog-to-digital converter (ADC) advertises an accuracy of the least significant bit…

A: Answer: We need to find the accuracy so we will see in the more details with the proper explanation.

Q: #3 in PSpice please and fill the table, thank you

A: the truth table is filled below

Q: Q1/A/ DM system is designed to operate 3times the Nyquist rate for a signal with a 3KHZ Bandwidth…

A: Provided the solution for both the above given questions, with detailed step by step explanation as…

Q: Find the maximum quantization error for PCM system that has a maximum decodable voltage of 1.8 V and…

A: Given: maximum decodable voltage of 1.8 V 12 bits to encode signal

Q: For a resolution of 0.032 V and an analog sample voltage of 4.030 V, complete the table below:…

A: Below I have provided the handwritten solution of the given question

Q: In what manner is the delay time quantified, and what units are used to describe it?

A: Latency: Latency is the number of seconds it takes a network to transport data from one device to…

Q: etermine the number of possible quantization levels if the number of bits per sample in a given PCM…

A: Quantization The process of quantization involves breaking down an analogue continuous signal into…

Q: Shown in Fig. P3.7-12 is the output of a data hold that clamps the output to the input for the first…

A:

Q: Figure (1) shows the block diagram of a wideband frequency mođulator using the indirect method. This…

A: Lets see the solution.

Q: Write an asembler program that samples a 1 KHz sine signal with 16 KHz and outputs t from DACO. DACO…

A: We can write an assembler program to do the given algorithm as follows: Initialize the DACO output…

Q: fm f₂. sinusoidal signal of frequency 800Hz is sampled at a rate of 4000 samples per second. w 1.5…

A: Given :- Sinusoidal signal of Frequency = 800 Hz Sample Rate = 4000 sample per second

Q: regions. Calculate the numerical values of the quantisation limited output SNR for the 4-, 8- and…

A: The SNR can be represented in a chart as follows:

Q: A multi-input multi-output digital system as in figure (project x) has 6- inputs (a, b, c, d, e & f)…

A: Final answer:

Q: Recall that the maximum input voltage for a 12-bit ADC on the TM4C is 3.3 V. If the input voltage on…

A: 1) We have 12 bit ADC 2) Max input voltage is 3.3V which generates 12-bit digital output of 0xFFF =…

Q: Signal to noise ratio is calculated as signal voltage divided by noise voltage Select one: O True O…

A:

Q: When pulse duration 0.001ms and fm 3KHZ ,the spectrum of the sampled signal is Your answer

A: 3

Q: A PWM signal has a period of 100 millseconds. The initial pulse width is 10 millseconds. This means…

A: Pulse width modulation is a powerful technique used to control analog circuits using digital…

Q: Case: It is requested to design and establish a communication network to receive the data (bits)…

A: IN ANSWER 1, SEE AT EXPLANATION BOX.  2. 1, SEE AT EXPLANATION SECTION.    The following problems…

Q: H.w/ find the 0/p of PCM for i/p signal x(t) the sampling frequency 5 kHz for 0<t< 0.1 s and eight…

A: Please find the attached solution belowIf you dont understand anything please do commentAll the Best

Q: Discretize the following continuous-time signal at an appropriate sampling rate, and then plot he…

A: According to the question we have to plot discretized version of the equation:   here, I'm using…