leplace heiWilrequivale fesisiois. THIS stepand help transform a complex comtinational nesistive circuit into a single equivalert resistanceIemenbering that series circuits are voltage dividers and paralled circuits are curent dividers.Procecdures:1. Comect the resistors to the power supply as reflected in figure 1.2. Measure the different parameters using the electrical measuring instrmert and devices andwrite your answerin table 1.3. Connect the resistors to the power supply as reflectedin figure 2.4. Measure the different parameters usirg the electrical measuring instrument and devices andwrite your answer in table 2.R1R21kQ10kQV1-10 VR3R46.8kQ33kQFigure 1. Resistors in series connectionV2=10 VR531koR6210kOR726.8kQR833kOFigure 2. Resistors in parallel connectionDiscussion of Results:1. Write the measured parameters in Table 1 for Figure 1.Table 1. Measured parametersResistorNo.ResistanceVoltageAmpereWatt(acquied uing the olmster/miti-ester)(acquind uirg thevoltrmeter / multi-tester)(acquind using theamter/ miti-facquired using thewattmeter)tester)1I ka210 k236.8 kn433 k22. Write the measured parameters in Table 2 for Figure 2.Table 1. Measured parametersResistorNo.ResistanceVoltageAmрereWatt(acquired using the ometer/miti-kster)(acquied irg thevoltmeter / multi-tester)(axpined using theanmter/ miti-tester)facquired uning thewittmeter)11 ka Figure 2. Resistors in parallel connectionDiscussion of Results:1. Write the measured parameters in Table 1 for Figure 1.Table 1. Measured parametersResistorNo.ValtageAmpereResistanceWatt(acquind uing the olmmter/miti-kster)(acquind uing thevoltmater / multi-tester)(acquind using theater/ miti-tester)facquired using thewattmeter)11 ka210 kf236.8 ka433 k22. Write the measuId parameters in Table 2 for Figure 2.Table 1. Measured parametersResistorNo.ResistanceValtageAmpereWatt(acquined Lsing the okmater/miti-kster)(acquireed sirg thevoltmeter/ multi-tester(acpind using theamter/miti-tester)faxquied unirg thewattmeter)1I kQ3210 k236.8 ka433 k23. Compute for the total resistance, total curent, total voltage, and total power of the systemin Figure 1.4. Compute for the total resistance, total curent, total voltage, and total power of the systemin Figure 2.Conclusion:

As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Discussion of Results: 1. Write the measured parameters in Table 1 for Figure 1. Table 1. Measured parameters Resistor No. Resistance Voltage Ampere Watt (acquind irng the omter/ miti-tster) (axguind uirg the voltrster / milti- tester) (acpind using the ater/ miti- tester) facquind ing the watmter 1. I ka 2 10 k2 3. 6.8 ka 4 33 kf2

Discussion of Results: 1. Write the measured parameters in Table 1 for Figure 1. Table 1. Measured parameters Resistor No. Resistance Voltage Ampere Watt (acquind irng the omter/ miti-tster) (axguind uirg the voltrster / milti- tester) (acpind using the ater/ miti- tester) facquind ing the watmter 1. I ka 2 10 k2 3. 6.8 ka 4 33 kf2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. What is a cold solder in electronics?2. What will happen if there is a cold solder? 3. What is a heat sink? What is its importance?
What is the difference between mid point and full wave 3 phase rectifier? Name 3 devices that can replace thyristor in the circuit.
Calculate the following a) V1 [1 b) i c) i2 Q17 The half wave rectifier is supplied with 230V, 70HZ signal. Assume the number of turns in the primary to secondary ratio is 7:2. i) Calculate the average de current through the load resistor 3KQ. Calculate the value of input ac power, output de power. 18. For the circuit shown in Figure B18, Vcc = 18 V, B = 110, Rc = 4.7 kQ and RB that VBE=0.7 V. 450 k2, assum %3! Vcc | Ic Ro RB Vc VCE
A) Determine all the electrical parameters of the circuit. B) with the results obtained, indicate the region of operation.
Below shows the circuit diagram of a remote control. Explain the operating concept of this simple circuit diagram and how it works to produce the signal.
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
please answer, this is about BJT ty
Determine the voltage across the resistor R2. (assume Zener voltage is 3 volts and Diode forward voltage is 0.7V)
take Vs=333V round off to 3 decimal places
For the network shown in Figure B22 , assume E = 18V, Diode D¡ as silicon and D2 Germanium, R1=3KQ and R2=2K2. Calculate, i. Current I,, ii. Current In2 ii. Voltage across resistor R2 R1 D E D2 R2 Figure B22 +
Quiz A.9 Consider a buck voltage regulator with duty cycle D=65% and Vi=7V The output voltage is: a)-13V b)- 20v c) 4.5V d) 20 V Give correct answer in 10 mins i will thumb up