د التجربة السابعة.pdfO 0 0 10 0 1 00 0 1 10 1 0 00 1 0 10 1 1 00 1 1 110 0 010 0 110 1 010 1 11 10 01 10 11 1 1 01 1 1 1Table 2-334. Set DIP1.0 to "LOW" and DIP1.1 to "HIGH". Repeat step 2. Compare outputswith step 2 between DCBA=0000~1001. Are the outputs different?DISCUSSION:1- Determine the logic required to decode the binary number 1011, by producing aHIGH indication on the output?2- A certain application requires that a four-bit binary number be decoder use 74154decoders to implement the logic.The binary number is represented as A,B,C and D?3- Design 4x10 decoder whish used to convert from BCD code to decimal?4- Design 3x8 decoder at active high using Enable line at active low?5- Design a BCD to 7 segment display decoder cct using NAND gate?5of ELECTRICLab. Name: Decoder CircuitUniversity of AnbarCollege of EngineeringDept. of Electrical EngineeringExperiment no.:7Lab. Supervisor: Arrak -M-IdanELECTRICAL1/0ENGINEERINGNT OFDEPA

Answered: Image /qna-images/answer/49a38b11-c894-4cef-bd33-f45f9c0dc1a1.jpg

Answered: DISCUSSION: 1- Determine the logic…

DISCUSSION: 1- Determine the logic required to decode the binary number 1011, by producing a HIGH indication on the output?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3a) Show the truth table for JK flipflop for positive edge clock triggering. 3b) if for time period T=1ms, level triggering clock signal changes as 10111 then show the output for the input, D=01001(Use D flipflop)3c) Make a 6-bit serial register.
Find VCe, VBe, and VCB in the following circuit: Rc 180 Ω Rg Vcc 15 V 3.9 kN BDc = 50 VBB 5 V
The control circuit functions to turn ON the light bulb whenever the binary inputs are even numbers between 1 and 15 in decimal. Other than that, the light bulb turns OFF. Design the logic control circuit of figure below. In your design, include: a)>The truth table deduced from the description. b)>The simplified output expression. c)>The logic control circuit using combinational logic gates. W Logic control X F Y• circuit > N
2// Explain the advantage's of Programmable Logic Devices?
Q2) convert the following: 1- decimal number to binary by using the repeated division by 2 method (49)10 ➜( ): 2- binary number to hexadecimal (10101010): ()16 3- octal number to decimal by repeated division by 8 method (254)→( )10 4- BCD code numbers to decimal (100101111000)BCD ( )10 5- Gray code to binary (1010)Gray ( )
Answer the below questions. a. What is the counting range in binary and decimal for an up-counter with 3 bits? b. What is the counting range in binary and decimal for a down-counter with 4 bits?
Question 3 a) Convert the following unsigned binary numbers to decimal. i) 101101112 ii) 010011012 iii) 100101102 b) Assume a digital to analog conversion system uses a 10-bit integer to represent an analog temperature over a range of -100C to 1000C. If the actual temperature being read was 36.5oC, what would be the closest possible value that the system could represent? Expiain the term aliasing and discuss how it can be avoided in digital sampling. d) Show the output waveform of an AND gate with the inputs A, B, and C indicated in the figure below. A B C
1- Determine the logic required to decode the binary number 1011, by producing a HIGH indication on the output?
A. X B What logic gate has the same function as the circuit above?
An eight bit number, 01011101, is: 1)added to 4 2) subtracted from -10 3) ANDED with 15 a) What is the outcome of these operations in binary? b) What is this number in decimal? c) What is the original number in decimal?
i need the answer quickly