Answered: Discuss the following in the design of…

Engineering

Civil Engineering

Discuss the following in the design of structural steel i) Bars and rods ii) Plates and flat bars

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Similar questions

Stress in segment bronze and steel
38. What grade of steel is preferred for the fabrication of most structural shapes other than W-shapes, and what are its yield stress and tensile stress? (Hint: See Figure 3.10.) 9.
The rigid bar 2 m long is supported by a steel rod at the middle B and bronze rods equidistant from both ends at A and C as shown. The properties of the rods are given in the tabulation below. Steel Bronze Allowable stress 140 MPa 120 MPa Modulus of Elasticity, E 200 GPa 83 GPa Area, A 400 mm2 900 mm2 Length, L 1,000 mm What is the required length of the steel rod so the reactions on the three rods are the same? What is the required length of the steel rod so that both the steel and the bronze rods reach their allowable stresses at the same time? What is the maximum permissible load W that the rods can carry?
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
Beam CX is subjected to a loading condition as shown in the figure. What will be the (a) the maximum tensile stress and (b) the maximum compressive stress in the Beam CX if its cross section is a T section with the given dimensions.
The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150 N/mm2, find the diameter of the middle portion and also the length of the middle portion if the total elongation of the rod is to be 0.2mm. consider the young modulus of a steel.
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
What is another term for bend? (A) flex B compress fracture D) twist E stretch
pls help me. thank u refer to the picture attached below.
A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure P-211 Aluminum A = 320 mm² 1.5 m 2P
Topic: COMBINED STRESS-AXIAL TENSION AND FLEXURE BENDING: STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9