Determine x for the cross-sectional area of the channel-shaped beam as shown in Figure Q3 and find the moment of inertia about the centroidal axis y.

Q: The diagram at the right shows vector F. If F =-Q, where Q>0, I(d) determine the value of F in terms…

A: The force F is making an angle of θ with +y axis  and x-component of Force = -Q where Q > 0

Q: *DO NOT USE THE PARALLELOGRAM METHOD* Find the direction and magnitude of the resultant

A: At θ=20°Force F1=100 ×10-3×9.81=0.981 Nin  Vectorial formF1→=0.981× cos 20° i^ +sin 20° j^F1→=0.939…

Q: Q1/ A. Write the force system for each one of the following? JIL

A: Given:-  To Find:-  Type of force system

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: Problem 3. a. A force has a magnitude of 1 kN and coordinate direction angles of 0,= 60°, 8, = 120°,…

A:

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A:

Q: If the resultant angle is known, then the formula to find the actual angle in a rotating system is O…

A: Let us discuss about formula to find resultant angle in rotating system.

Q: Draw the three projection in sheet

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Need help with both questions, include all steps and units please and thanks.

A: Step 1:Coordinate angle γ is 36oAngle θ is 24oThe force acting along a-a is −43i^+52j^​+62k^Step…

Q: FA -X B FB Alpha = 34 degrees

A:

Q: Q1. Force F = {270i + 450j –140k} N and it passes point B. The coordinates of the points are: A (21,…

A: Given: The force acting, F = (270i+450j-140k) N The distance between O and B, OB = 21 cm The…

Q: 1. Give the rectangular coordinates of the point C (p = 4.4, q = -115, z = 2). 2. Give the…

A:

Q: 7. Using the formula R = √ (r² + s²/4); solve for r. Page #

A: Given:To find:Solve for r.

Q: HomewoTK: 1. Find the line L passes through the point (1,2) and parallel the line L: X +2y = 3.

A:

Q: Find the angle between lines AB and AC where the point A(3, 2, 3), the point B( – 4, 6, 6), and the…

A: Write down the coordinates of point A, B and C.

Q: e resultant of the moment

A: Determine the resultant of moment.

Q: Q1: Consider the points A, B, C, D where coordinates are respectively (1,1,0), (-1,1,0), 0,-1,1).…

A: According to the given  information solution is given below…

Q: For the stress states above determine the required yield strength of the material based on the…

A:

Q: If f C2)= x3+x find f (1) + fG

A:

Q: Q1/b/ * Q1/b): If at location B the car move at constant velocity.. So the angle a equal to: * 30…

A:

Q: Q5/ Find the volume of the Tetrahedron that is determined by three edge vectors ä = [1, 0,-3),…

A:

Q: Find the angle between the two given vectors. u = (1, -4, 1), v = 3(0,2, -2) Write your answer in…

A:

Q: 1 d. The point A has coordinates (4, 1), AB = 9 5 BC Find the coordinates of B and the column vector…

A:

Q: (f) s+2 85-384 +2s³

A: f(s)= s+2s5-3s4+2s3

Q: Problem 3: Note: Make sure to draw all diagrams. All Units must be included. Determine the magnitude…

A:

Q: Q1: A position vector has a length of 40 m and is at an angle of 57° above the x- axis. Find the…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.