Answered: Determine vo and the required PIV…

Determine vo and the required PIV rating of each diode for the configuration of Fig. 2.173. In addition, determine the maximum current through each diode.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: For the circuit in the figure below, in which the diode has a value Vd = 0.7 V: Calculate the…

A: In this question, we need to determine the two values of output voltage Vout . Also determine the…

Q: 4) Please determine the following parameters according to the zener diode circuit which is given…

Q: Determine the voltage across the silicon diode assuming the practical diode model. Write the answer…

A: it is given that:

Q: ideal diode Es R 120V f* 60 Ha what is the maxinum value of the inverse volTage of He diode if the…

A: In this question we need to find a maximum inverse Voltage across diode when diode is blocked. I.e…

Q: Determine the forward voltage and + V, - forward current for the diode in the R1 Ej = 10 V oV 4.7 k2…

Q: For an ideal diode which of the following is true? a) It allows the passage of current in the…

A: In the following sections, among the given statements, which are true for an ideal diode will be…

Q: Question3: Based on diode i-v characteristics measurements we found: Va = 0.65V, ia= 0.684mA Va =…

A: For a forward biased diode :- I=IseVnVT-Is Since the value of IS in forward biased diode is very…

Q: For the circuit shown, find the load voltage, load current and diode power using third…

A: We have an circuit as shown is figure we have been asked to find, Load Current Load Voltage Diode…

Concept explainers

Voltage Division Method

In the electronics branch, a voltage divider is required to produce a section of its input voltage as an output. This basic circuit may be prepared with two resistors or any passive elements along with the voltage source. The circuit resistors are attached in series and a voltage source is braced across these resistors. The input voltage can be transferred between the resistors in the circuit for the voltage division to occur. The SI unit of electrical resistance is ohm (Ω) or kilo-ohms (kΩ).

Question

29. Determine v, and the required PIV rating of each diode for the configuration of Fig. 2.173. In
addition, determine the maximum current through each diode.
100 V
-100 V
FIG. 2.173
Problem 29.
Ideal diodes
2.2 ΚΩ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Ideal diode basic property.

VIEW

Step 2: Equivalent circuit during positive input voltage and negative voltage.

VIEW

Step 3: Peak inverse voltage accross each diode is given by below circuit.

VIEW

Step 4: Out put voltage Vo calculation

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is a solid-state diode tested? Explain.
Consider given choices. Solve the current flowing to silicon diode of the given circuit below.
Question 2: (show your detailed answer for each part of questions below) a) For the series diode configuration in the figure below, determine VD, VR and Ip. + Vn Si 10V 3 kn V b) Calculate the current through a 70 2 resistor in the circuit shown in the below figure. Assume the diodes to be of silicon and the forward resistance of each diode is ta-1 2 Show the answer steps. D Dz 70 n www 20 V DA Dy
4kN 2V Determine the state of diode for the circuit shown. find ID and VD. Assume simplified model for the diode. (Diode is Silicon). 4k2 2V 1k2. 0.7V O -0.375 mA, 0.4 V, off O -0.67 mA, -0.24 V, on O -1.5 mA, 0.7 v, off O 2.04 mA, -8 V, on
5 نقاط Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 R1 :: D2 9kQ.. 1N1199C ..... ... R2 D1 .... .... ... .... 18KQ 1N1199C V2 12 V R3 1kQ D3. 1N1199C ... R4 5kQ ..... .... .... .. .. ... .... .. .... .....
Draw the output voltage waveform of the circuit given below. Calculate the Vdc value. 100 V Ideal diodes -100 V 2.2 k2 2.2 k2 2.2 k2
Diode Configuration + Vp IR Si b.1 For the series diode configuration, determine: Vp, ID, and VR. Use the approximate model of the silicon diode. Ip E 8 V R 2.2 k2 VR
Note: The diode is silicone. Complete explanation please thank you
Using the ideal diode model, find the output voltage for the input voltage of the following circuit and graph it in detail. (a) (b) R₁ D₁ www ww R3 D2 (a) R₁ D₁ www + + D2 R2 vo Vo R₂ (b)
For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy, VD4 and ID2. 15V 15V Allt V1 V2 R1 1k IDC 1mA Vx R2 2k ww D1N4002 Vy D1N4002 7D1 D1N4002 D2 D3 R3 1k D4 D1N4002
Please answer all subpart either dislike is ready Please answer in typing format please ASAP for the like please Please answer in typing format please
A current of 5 μA flows through a p-n junction diode at room temperature when it is reverse biased with 0.15 V. Calculate the current flow when it is forward biased with the same voltage. a. -1.65 mA b. +1.65 mA c. +0.15 mA d. -0.15 mA