Determine the Xbar and Ybar of the shape seen below. W = 7 in h = 7 in D= 4 in

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: , I want to know what would be the perfect size to put a bushing in a hole. The bushing will have a…

A: To find-: The perfect size to put a bushing in a hole. Given-: The dimension of the hole is h=0.50…

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: 4 (7) Czar (10) 8

A: Given: There is shown a milling machine in which we have to find out the different names of the…

Q: For the stress element below, when a = 6, b = 4, and c = 6, the principal stress σ1 , the largest…

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: 3

A:

Q: 1. A tension-controlled concrete member is one in which the tensile strain in the steel reaches at…

A: (1) According to he ACI code the tensile train in the steel must be reached to the value of at least…

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: Determine ly and ky.

A:

Q: 15 kN 20 kN 2 m m

A:

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: 13378.2898 lbm to lbf

A:

Q: Lacate the centacid of the blane sheded ora shown below

A: Given Data The radius of the quadrant is: r=16 cm The side of the internal square is: a=8 cm To…

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Q: Q4. The compound shaft shown in Figure Q4 is attached to rigid supports. For the bronze segment AB,…

A: As per Expert Q&A guidelines we are supposed to answer the first three parts of the given…

Q: 40 7 slug 110 dyne

A: given:

Q: 1- The newton's second law is (a) F= ma (b) M =Fd (c) N.M 2- The unit of mass is: (а) Kg (b) L (c) S

A: (a) F = ma (a) Kg (a) N/m2 (a) N (a) F.d

Q: At a certain instant, the particle of mass m has the position and velocity shown in the figure, and…

A:

Q: Part II. Longer problem focused on problem solving multiple steps. This problem will be graded based…

A: Step 1: Step 2: Step 3:don't forget to upvote :) thank you and comment if doubt exists Step 4:

Q: Determine Ixx and lyy for the composite section shown below. 50 mm 25 mm 30 mm 25 mm 50 mm 50 mm

A: Given figure

Q: 5と 2' 111ド 7K 8'一 16- 251

A:

Q: D= 1.75 in d= 0.75 in r= .120 in

A: Calculate D/d and r/d ratio, Fr calculating the stress concentration factor we use the…

Q: 2x105 Nlmen2 Biomaha uemprog aoo un qans G ) Tatal anctansion the ban

A: Normal stress is defined as the intensity of force exerted on an area perpendicularly. Normal stress…

Q: The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke each piston is 125…

A: given:diameter d=45mml=125mmCR=8.75

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.