Determine the width of a carbon resistor having a sheet resistance of 15 0 12 if the length is 1/2 in. and the resistance is 500 2.

Q: The figure4 shows the relation between resistance and temperature for the thermistor.…

A:

Q: As the doping of a pure semiconductor is increased the resistance will Answer:

A: For a pure semiconductor if doping is increased, either free holes or electrons are created. These…

Q: 1. Determine the current for each of the circuits by using practical equivalent model of diode. b)…

A:

Q: 40V I02 02 R1 10 kQ D2 D1 R2 R2 10 k -10V -10V CIRCUIT - 02 CIRCUIT-01

A:

Q: 9V 2kn Find Voltage output and current? (diode is silicon) 8kn Vo 5V 5ka

A:

Q: The diodes in the circuit are all Silicon with forward voltage of 0.7 V. If R1 = 60 and R2 = 140,…

A:

Q: What is the fanout value of the IC that has IOL = 10mA, IOH = 5mA, IIL = 100uA, IIH = 100uA current…

A: Given: for an IC IOL = 10mA, IOH = 5mA, IIL = 100uA, IIH = 100uA

Q: Assume the diode emits green light when drawing 100ma of current. Assume Vcc=6V. What is the value…

A:

Q: Find the current through the diode in mA. Blank 1 Answer must be with 2 decimal places. Do not…

A:

Q: Determine whether the diode is conducting or not. Assume thatthe diode is an ideal diode.

A: Concept , References and Examples: Examples-1Examples-2  Thank you

Q: What special type of diode is used in the circuit? Given the state of the switch as shown, what is…

A:

Q: Ik 1k ww ww-

A: Here given V and assume zener diode in breakdown region  then apply KCL

Q: Table 3 6. Plot the values from Table 2 and Table 3 on the same graph done in step 3. Does the diode…

A: Diode is device which is made of semiconductor, basically it act as switch

Q: If you have a diode of power rating 10 mW. The voltage across it is 0.7 V and the current passing…

A:

Q: Orange Black Brown Silver

A: Introduction: Resistor: An electronic component called a resistor is used in a circuit to control…

Q: Resistivity of a wire depends on length material O all of the above. O O O

A: Resistivity of the wire calculated as : R=ρlAwhere,ρ = resistivityL = LengthA= area

Q: The resistance of a 125 2 strain gauge changes by 1 ohm for 4000 micro strain. The gauge factor is…

A: Given: The resistance, R=125 Ω. Change in resistance, ∆R=1 Ω. Strain, ε=4000×10-6.

Q: 1. Using first approximation, find the voltages across resistance. 2. Using second approximation,…

A:

Q: Find power supplied to all of the diodes. D2 Si D3 R1 D1 5002 2V GaAs R2 D4 V1 1k2 Si 7V

A: Considering ideal diodes, the diode D1, D3 and D4 are forward biased and the diode D2 is reversed…

Q: Using the ideal model for the diodes, what is the current I in milliamps if V₁=2.5 volts and V₂=8.0…

A:

Q: if diodes are silicon diodes, what is the voltage across R? express answer in volts 10 V= D₁ D₁ (i)…

A:

Q: A copper wire has a resistance of 2.4 ohms at 20-deg. Find its resistance at 75-deg. Resistance…

A: In this question we need to find a resistance of wire at 75°C

Q: Q3: Determine the currents I1, I2, and ID2 for the network of figure. the diodes are assumed to be…

A: We need to find out the current for given circuit.

Q: The resistance of a copper wire is (0.92 N) at a temperature of (4 oC). At what temperature will be…

A: The resistance.and temperature dependence of the metals is explored and hence the temperature at…

Q: Assuming that the diodes in the figure are ideal, what will be the current in d1

A: For solving this type of problems,we must assume the diode on off conditions as fallows,if our…

Q: The length and diameter of copper wire are found to be 100 and 0.002 m respectively consider that…

A:

Q: What is the current through the diode? 1 N 2 IDEAL_DIODE R1 12 kn 12 V

A:

Q: The diodes in the circuit given below are identical and each one is ideal. Accordingly, determine…

A: For first circuit shown below:

Q: Calculate the current flowing through the circuit and the voltage value at the V0 ends. (Threshold…

A: Here let us assume initially we have assumed that both the diodes are turned on .   After…

Q: Both D1 and D2 are silicon diodes with forward voltages of 0.7V. Vi is the input, and Vo is the…

A:

Q: The power dissipated in Diode D1 is D2 power R 1k ww D₁ 1N4007 230 V AC 100 k D₂ 5.6V, 400 mW eeeee…

A: We need to select correct option

Q: Problem 5. Calculate the cross-sectional area, in mm², of a piece of copper wire, 40 m in length and…

A: it is asked to find the cross sectional area of given copper wire in mm2

Q: R1 10 k2 D1 D2 D3 A C В I3 R2 R3 10 k2 10 kQ O -20 V O -10 V

A:

Q: Determine the current through R1. Use practical diode model.

A:

Q: The value of resistance in insulators is O a. small O b. large O c. can not be determined O d. zero

A: The electrons in the insulator's atoms are strongly bonded and cannot travel easily. Other…

Q: When a pure semiconductor is heated, it's resistance: a) goes down. B)changing every time. C) goes…

A: In this answer let us try to understand what happens to the resistance of a semi conductor when it…

Q: 11 R2 1K R1 D2 1K 5V D1 Determine the voltage across the resistor R2. (assume Zener voltage is 3…

A:

Q: Determine the forward voltage and forward current for the diode in Figure 1 below for each of diode…

A: We need to find current and voltage for given circuit in different cases.

Q: Plz answer correctly ....

A: Step 1:Step 2:

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.