Determine the viscosity of the gas mixture in TABLE 1 at 200 degree Fahrenheit and a pressure of 1 atm.

Q: Density and viscosity oleic acid at 20 degree celcius and 1 atm

A: Oleic acid is an mono-unsaturated long chain fatty acid which is generally found in liquid state at…

Q: Calculate the density of oxygen gas at a temperature of 57 C and a pressure of 5 MPa.

A: Density of oxygen at 570C and 5 MPa is asked

Q: An oil is used to lubricate a thin plate with a surface area of 5.382 ft² that is placed between two…

A: The shear force acting on the upper side and lower side of the thin plate is determined. The total…

Q: An oil burner nozzle is labeled 60°. This is the angle from straight ahead tothe direction that the…

A: Paper is placed 12 inches from the nozzle.  the oil burner is labeled at 600C, The Schematic of the…

Q: Describe the difference between average pressure and false pressure

A: The force applied perpendicular to the surface of an object per unit area over which that force is…

Q: Q.5 Calculate the wall thickness of a fermenter with the following materials of construction: a) low…

A: Hello. Since your question has multiple parts, we will solve first question for you. If you want…

Q: As a solid melts into the liquid state,    the particles maintain their fixed volumes  the…

A: As solid melts into the liquid state, the particles experience an increase in their kinetic energy.

Q: It is said that inlet gas takes 5-6 turns in Cyclone Separator.Justify the statement.

A:

Q: A valve chokes refrigerant 134a from 0.7 mPa to 160 kpa. Determine the temperature released by the…

A:

Q: Estimation of the viscosity of a dense gas. Estimate the viscosity of NITROGEN at 65°F and 1000…

A: It is given that nitrogen gas is at temperature of 65oF and pressure of 1000 psig.

Q: If a spherical drop of liquid evaporates at a rate proportional to its area, if initially its radius…

A: Let V and S be volume and surface area of the spherical drop whose radius at time t is r Given…

Q: Why the temperature of the gas exiting the CSTR is different from the temperature of the entering…

A: Constant stirred tank reactor (CSTR) is a continuous, perfectly mixed reactor.

Q: heat conduction

A: Heat Conduction is the transfer of thermal energy from higher temperature to lower temperature in…

Q: If you are in an open place where the wind is blowing at 38 km/h and 12 °C, considering that at the…

A: Given Wind speed,U=38km/h T1=12 °C Skin temperature T2=28 °C Arm dimensions=122 cm long and 7600 mm…

Q: 3. A vertical furnace door, 1 m. in height has a surface temperature of 120°C over which air (30°C)…

A: Given height of the door = 1m surface temperature = 120°C air temperature = 30°C air velocity = 2.5…

Q: The inner and outer surfaces of a pane of plain glass, which is 0.4 cm thick and has an area of 2 m…

A: Given, The area of the glass, A = 2 m×2 m = 4 m2 The thickness of the glass, ∆x = 0.4 cm The…

Q: What happens to the vapor pressure of a substance when its surface area is increased at constant…

A: The effect on the vapor pressure of a substance as its surface area increased is to be determined…

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: / Air ine room with dimensions are 4 mx 6 m x 3.5 m have density of air is 1080 g/m². Calculate the…

A: We know  that, Density = Mass/ Volume Where,  Density = 1080 g/m3

Q: 5. Absolute pressure is measured relative to atmosphere. Tor F

A: Absolute pressure is measured relative to a full vacuum Whereas the pressure that is measured…

Q: Temperature measurement is done using a mercury thermometer; which is protected by a thermowell.…

A: The order of mercury thermometer is to be mentioned with detailed analysis.

Q: 2) A cylinder holds 200 kg of water at 120 °C at a pressure of 20 MPa. The temperature is increased…

A:

Q: In a soil with a thermal diffusivity of 5.16 x 10-7 m ^2/s, and which is initially at a uniform…

A:

Q: 1. Determine the specific enthalpy of water for steam at 10.5 bars absolute pressure in bars.

A: As we know from the saturated water and steam table the value comes out to be or directly taken from…

Q: pars), calculate the

A: Given data: mole% of water in overhead stream=8.5 mole%Pressure; P=34.7 psia=2.36 bars

Q: what is the area/diameter of a p6227 venturimeter

A:

Q: separated from the plane with a film of oil of thickness 1.5 mm. The plate weighs 30kg and slides…

A:

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Cv = 20.8 J/K.mol Cp = 29.1 J/K.mol Initial temperature = 50K Final temperature = 100K Find…

Q: The pressure drop required for fluidizing a coal bed with a liquid petroleum fraction of viscosity…

A:

Q: 17.17. The fins on the radiator of your car are about 2 in long. When your car is going 60 mi/h, the…

A: length of fin x=2 inchvelocity approaching the fins  v=40 mi/hr = 17.88 m/s

Q: Define the temperature of liquid nitrogen exposed to the atmosphere remains constant.

A: Liquid Nitrogen - Temperature -195.79 oC( 77K , -320 oF ). This the boiling point of liquid…

Q: On which factors does the liquid composition at the bottom of the tower depends?

A: Packed tower are the mass transfer device are composed of packing material having high surface area…

Q: Calculate the viscosity (micropoises) of molecular oxygen at 273.2 K and 1 bar. The molecular…

A: Given that, Temperature T = 273.2 K Pressure P = 1 bar Molecular diameter d = 0.360 nm = 3.6 × 10-10…

Q: Calculate the viscosity of oxygen at 350 K and 1 atm pressure using equation 7.12 on page 90 of the…

A: Given data: Temperature = 350 K Pressure = 1 atm

Q: Difference in temperature ( AT ) Cº ( with sign ) ?............ Difference in distance between test…

A: The graph given for the measurement of the thermal conductivity of steel is given as: Here, the x…

Q: 3- A rigid vessel contains fluid at 1 MPa and 260 degree with a volume of 0.14 m³ is cooled until…

A: Initial pressure (P1) = 1 MPa = 1000 KPa Initial temperature (T1) = 260°c = 533 K Volume of rigid…