determine the value of Mo.

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: Please make draw the right-side view, front view, and top view of the given isometric drawing.…

A:

Q: 300 mm 30º 300 mm 300 mm Can someone please label the projection of F and the rest of the…

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: Part B - Analyzing the force-couple system on a bracket For the bracket shown below, Fi = 165 lb, F…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. please…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: What are the different systems of Units?

A: The different system of units are listed below: SI system MKS system FPS system CGS system The SI…

Q: what is the bottom length?

A: To calculate the bottom length

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: 3- The plane in the space is determined by three points that are not on straightening one O right…

A: Explanation: 3) A plane in space is determined by three points that are not in straight line.  For…

Q: Is this for number 1 only?

A:

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: Which of the following statement is correct in terms of degree of freedom? Select one: O Moving left…

A:

Q: What is the degree of freedom of the two questions

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.