Determine the tension in the string and acceleration of the block A and B weighing 1200 N and 400 N connected by a string as shown in figure Assume pulleys are weightless and f

Q: The following particulas apply to an inclid belt conveyor length of conveyar (locdling end to…

A: given; →wrap angle(θ)=2200                     =220*π180                     =3.837 rad→maximum…

Q: A centrifuge is often used for astronaut training. A simplified version is sketched in Figure P3-22,…

A: As the cockpit is rigidly fixed to the arm, there won't be any Coriolis component of acceleration…

Q: notation, determine the velocity of mass C, and the angular velocity of bar BC when 0 = 30°. %3|

A:

Q: tl-25 ms t-21o ms F(N) t2=50 ms t3=125 ms Striking Pushing off t4-200 ms ts-210 ms =11N F=5.5 N F-…

A:

Q: (12) What is the value of F? (A) 7.53 N; (B) 8.03 N; (C) 8.53 N; (D) 9.03 N; (E) 9.53 N.

A: 12. According to the given data, Pressure is similar for both cylinders. Therefore,

Q: Problem #1 The 1.5 Mg four-wheel-drive jeep is used to push two identical crates, each having a mass…

A:

Q: Find TF to the mechanical system below? K 0000 Se M Riy

A: Given:To determine the transfer function of the given system.

Q: Need help with this Question ( Use image below) Solve correctly for an Upvote round to 3 sig figs…

A: Given: Free body diagram of system,

Q: nasses m1, m2.m3 and m4 0 kg, 240 kg and 260 kg aly. The corresponding radi e 0.2 m, 0.15 m, 0.25 m…

A: Given : m1= 200 kg m2= 300 kg m3= 240 kg m4= 260 kg r1=0.2 m r2= 0.15 m r3 = 0.25 m r4 = 0.3 m…

Q: 5. The two-pulley system is shown to the right. Pulley A starts at 5 rpm and accelerates at a…

A: The diameter of the pulley-A at the belt is DA=4 inThe diameter of the pulley-A at the belt is DB=2…

Q: Q6 Figure Q6 shows the masses of the boxes are ma = x kg and mp = y kg. The coefficient of static…

A:

Q: Q11/Four masses A, B, C and D as shown below are to be completely balanced. A B C D Mass (kg) Radius…

A:

Q: 1. The following figure shows a four-bar linkage mechanism with its dimensions. Determine 03 and 04.…

A: The dimensions are

Q: Direction: Solve the following problems completely. Include all FBD with proper labels. 4 decimal…

A: Given Information Mass of block B = 500 kg Angle of Friction = 12o Mass of block A is negligible…

Q: 50000 kg

A: m1 = 60000 kgm2 = 55000 kgm3 = 50000 kgk1 =100000 kN/mk2=60000 kN/mk3= 30000 kN/m

Q: DRAW ONLY THE FBD OR FREE BODY DIAGRAM FOR THE GIVEN FIGURE. COMPLETE FBD WITH LABELS. WRITE LEGIBLY…

A: Free body diagram is the diagram of a system which shows all the forces acting on the system.

Q: 2) Compute the effective inertia that a clutch must transmit to accelerate a 54-inch solid shaft…

A: Introduction: The ability of a body to resist angular motion about an axis is defined as its moment…

Q: oblems 10-16 Information: Jose' pushes a wheelbarrow consisting of a wheel (mass mw = 3 kg, radius…

A: Jose' pushes a wheelbarrow consisting of a wheel (mass mw = 3 kg, radius r= 0.1 m) and a barrow body…

Q: Figure Q4 shows a racing car with a mass of 975 kg that was tested for the naximum acceleration it…

A:

Q: orque is the ratio of force and the perpendicular distance of its line of action from the given…

A: Given data Torque is the ratio of force and the perpendicular distance of its line of action from…

Q: In the figure below, C and D represents brakes, which can be used to stop the rotation of either…

A: C represent gear 4  D represent gear 8 T denotes Teeth in this solution And N denotes rpm

Q: 1) "Fuel is spent to make the vehicle go uphill, as you are aware. However, the fuel will not be…

A: As we know thermodynamics is a branch of engineering that deals in heat, heat output like work, heat…

Q: Plz solve correctly all parts Will definitely upvote Don't use chat gpt

A: Analyzing the Tension in the String (Part A)The system you described involves multiple masses and…

Q: Problem #2: Given the following pulley-elevator system HINTS! Zfy =o =O ZMO T₁V=IA (2) W = 5 kg J N…

A:

Q: 1. Consider the system shown below. Block A weighs 95.0N and block B weighs 55.0N. Once block B is…

A:

Q: While driving, a driver with no seat belt nor air bag hit the windshield and the contact time was…

A: Given data: t=0.3 millisecond=3×10-4 secvi=30 m/svf=0 m/sm=80 kgM=1500 kg Need to determine the…

Q: 4. For this series of 4 questions, two blocks, A and B, are connected using the cable and pulley…

A:

Q: What is the tension in the cable in units of lbf ?

A: The coefficient of kinetic friction between the support and Block =0.1 Acceleration of the Block B…

Q: The ball sorting device shown essentially is an in-line crank-slider mechanism. If the distance S…

A: From the given configuration diagram, assume different points as shown below. Here, 'O' is the…

Q: In the crank-slider mechanism below, what is the range of motion of the slider (the distance between…

A:

Q: Q5: Explain the Angular Speed Measurement Devices.

A: Explain the angular speed measurement devices

Q: Locate all the centros & determine the linuar velocities of prints C, D&E in A/min & angular…

A:

Q: Question 1 Determine the radius of curvature p at point A. Work in meters. Question 2 Determine the…

A: Given data:- Mass = 90 kg Speed = 4 m/s Find  1- radius of curvature. 2- normal force on toboggan.…

Q: Calculate the ankle torque during initial contact when running from the following data set to 1…

A: To determine the ankle torquethe following data isankle, ankle

Q: a. Define the following term 1. Lateral vehicle dynamics 2. oversteers 3. steering wheel shimmy…

A: Lateral Vehicle dynamics  This is the study of vehicle dynamics that cause the lateral motion or…

Q: #4 Balancing Torques 0.0 1.0 2.0 3.0 4.0 5.0 6.0 3.2 N 1.5 N 2.5 N in the the fulom (niuot the 2.0

A: given

Q: Determine the equivalent spring constant (N/m) of the whole system shown if k1 = 19.69 N/m, k2=…

A: k1= 19.69 N/m k2= 27.45 N/m k3= 38.96 N/m k4= 45.2 N/m k5=58.63 N/m

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.