Determine the tension in the cables. Solve this problem using twosolutions methods –force triangle method and analytical solution method.

Q: Find the maximum value of mass attached to the string,

A: Given data:

Q: 04-Neglecting friction forces, and the radius of the pulley. Determine the following: 1- The tension…

A:

Q: 8. For the plane truss loaded as shown below, use the method of joints to calculate the force in…

A:

Q: Determine the force in member AE of the loaded truss. The force is positive if in tension, negative…

A: Given,A loaded truss in which a load of 4.2 KN acts at B and a load of 2.3 KN acts at C.To Find -…

Q: D 7.5 ft B 10 ft 5 ft 12.5 1000 lb

A:

Q: Find the support reactions and joint force of the construction, shown on the figure, if 4-24 kN/m,…

A: Given data: q=24 kN/mM=25 kNmL= 3 m

Q: E Find the Reactions at pont A where the tensile force in cable CB is 300 KN. Neglect weight of AB.…

A: Consider the Free Body diagram:

Q: A steel cable is used to pull an 800kg car across

A: Given:  Mass of Car=m=800kg Maximum tension in the cable=3600N The given problem belongs to kinetics…

Q: A vehicle of mass 21 tonnes runs into a buffer stop having two buffer springs connected in series…

A: Given data: -  The mass of the vehicle is m = 21 tonnes. The stiffness of the spring 1 is K1 = 1300…

Q: Problem 1 Determine the reaction at A and C. Support at A is fixed, C is roller support, and B is…

A:

Q: Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal…

A:

Q: PE Problem for Module 2.1: Solve the complex truss below by the method of substitution. See…

A: Since H is a compound truss, therefore by  substitution method,  substitute member ad with one…

Q: 2. Compute the reactions at the pin B and at the roller A. A 30% 8 ft 800 lb ft -4 ft- B 390 lb 13…

A:

Q: The expert has sketched FBD after cutting the truss as shown in the image (using sections method).…

A: In a method of the section, only those bar is taken as a force who is being cut. It does not mean…

Q: 3. Find the force in compression strut AC and tension cable BC below using the closed force triangle…

A:

Q: At a building site a 1-ton container hangs from a crane wire and is then placed on the floor so that…

A:

Q: It is required to design a helical torsion spring for a window - shade. The is made of patented…

A: Given DataMb=250N-mmE=207GPak=3 N.mm/radD=18mmfs=2

Q: (1) The orange arrows are the forces which are 7 kN.   (2)There's a pin at lower left corner.…

A: In an equilibrium condition of a rigid structure like a frame or truss, the sum of all horizontal…

Q: The 1.5 kN vertical OA pole is supported as shown in the figure and loaded with a horizontal force…

A: Given: The weight of the pole is 1.5 kN. The pole with the supported load is shown below:

Q: The weight shown below is 1000 lb, attached to a cable at E, running througha smooth pulley with a…

A: Given data W=1000lb

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A:

Q: 3. Several blocks are resting on a simply supported beam. Determine the reaction forces. each…

A: To find : The reaction forces acts on the beam. Given : The mass of each block is m=50 kg. Free body…

Q: Provide step-by-step solution with complete given and formula to this problem.  Draw sketch also.…

A: Given DataL=328 ftd=1.75 inW=8×103×2.2=17.6×103 lbsV=525 fpmt=10s

Q: Q1: A: Draw a Free Body Diagram of the bars AD and BC shown in the figure. Assume all hinges to be…

A: Solution:

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: The given force in vector is The position vector of the force can be determined as shown below.

Q: A wheel of 10 in.radius caies a load of1000 lb. a. Determine the horizontal force Papplied at the…

A:

Q: Problem 4-17: The pipe is stuck in the ground so that when it is pulled upward the frictional force…

A: To findDetermine the initial force P required to pull the pipe out and the elongation just before it…

Q: Q4) Calculate the force T in the cord at C needed to support the loaded truss. Also, find the forces…

A: The Joint Method. The joints technique is a methodology that is used to solve unknown forces…

Q: Hello expert! Please show complete step-by-step solution; because I want to understand the process,…

A: Given System of truss  To find Force in each members and state Support

Q: Two cables are tied together at C and loaded as shown in the figure. If the weight of the load is 10…

A:

Q: 1. A crane rail moves a 900 kg crate in a warehouse First, answer the questions below, then derive…

A: Mass of crate =900 kg Weight of crate Wcrate = 900 x 9.81 = 8829 N To find out:- 1. What type…

Q: Calculate the forces arising on A, B and D pins with the effect of 500N horizontal force in the…

A:

Q: 22. Find the force in members AB and BC. 3.5 m -400 N 45% 3.5 m

A: