Determine the steady-state output response of the causal system H(s) given below to an input æ(t) = m/2 cos(wot + d°)u(t). H(s) = (stun)" Fill-in the blanks below and express your answers using algebraic operations involving m, d, and constar values. Yss(t) = cos(wot+ Ju(t) Note: Use positive constant/s for the magnitude as the answer to the phase assumes that the constant you are using is positive.

Determine the steady-state output response of the causal system H(s) given below to an input æ(t) = m/2 cos(wot + d°)u(t). H(s) = (stun)" Fill-in the blanks below and express your answers using algebraic operations involving m, d, and constar values. Yss(t) = cos(wot+ Ju(t) Note: Use positive constant/s for the magnitude as the answer to the phase assumes that the constant you are using is positive.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given the discrete-time sinusoid a (n) = 2cos(nn/2) + sin(3nt/4), ignoring the effects of aliasing, if this was due to sleeping rate F, = 70 Hz. What are the frequencies of the continuous time cosine and sine functions? O a. Cosine is 35.00 Hz, Sine is 52.50 Hz O b. Cosine is 23.33 Hz, Sine is 52.50 Hz O c. Cosine is 23.33 Hz, Sine is 46.67 Hz O d. Cosine is 35.00 Hz, Sine is 46.67 Hz O e. Cosine is 35.00 Hz, Sine is 105.00 Hz O f. Cosine is 23.33 Hz, Sine is 105.00 Hz
In order to reduce the steady-state error of a system, a lag compensator was designed as shown. Determine the steady-state errors for a ramp input before and after adding the lag compensator. Hint: use Kv R(s) Select one: O a. 1 and 0.3 O b. 1 and 0.2 O c. 1 and 0 O d. 2 and 1 O e. 2 and 0.5 S+ 0.1 s+0.01587 lag compensator 0.7936 2 s(s+ 1)(S + 2) plant C(s)
а 5-657 0 1 2 3 4 5 6 7 5.657 Real part of (x(n)) -5.657 Zmaginary part of 2 (m) 0 1 2 3 4 5 6 7
find a response i lt) at steady state of the circuit ad the value i, l0.5 ms) set to W= 500 rad/s l00 O to lo v
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
|| For the circuit shown in the figure below, assuming that VA = ∞, the input impedance is expressed by: Vcc O O Q₂ Rc Vino O Select one: Q₁ a. Vout 1/9m1 b. 1/9m1 + BRc 1/9m1 + Rc None of these O c. O d. V₂
Calculate the capacitance of the circuit below.
Thanks
Given the circuit below and the associated set of voltages and currents, the real Power delivered by the independent voltage source is V3 10 j2 N + j3 N 12ΩΕ V1. 39 I, -j16 N V, = 150 /0° V Vi (78 - j104) V V2 (72 + j104) V I, = (-26 – j52) A I, = (-2 + j6) A I = (-24 - j58) A V3 = (150- j130) V Copyrighe 201st Peirse Ecation inc putlishing as Piene Hal Note: The given values are not RMS values.
i need the answer quickly
Find out following:i. Sketch the root locus.ii. The number of branches of the root locus.iii. The value of ? and gain ? where the locus crosses the ??-axis.iv. The breakaway and break-in point on the real axis.
a. For the circuit shown below: 20 2 1 mH ll R Vs (*) 100cos(2001) V 25 mF the following LTspice netlist can be used to determine the magnitude and phase angle of the steady-state ĀC part of v: Vs 3 2 AC 100 0 R 3 0 20 L0 1 1m C 1 2 25m .AC DEC 1 31.83098861 31.83098861 Run the simulation and identify the desired results in the output file. b. Use the phasor analysis method to determine the analytical solution, and verify that the LTspice result is correct.