Determine the spring stiffness K in N/m to maintain equilibrium of the scissors linkage. The linkage is subjected to a force of P = 800 N. The spring is un-stretched when initial angle θ0 = 10º. Neglect the mass of the links. Determine the spring stiffness k in N/m for equilibrium when θ = 65º.

Q: Each spring has an unstretched length of 2 mm and a stiffness of k = 350 N/m. Determine the…

A:

Q: Determine the magnitude of the force P required to maintain the equilibrium of the two bar linkages.…

A: The objective of the question is to find the magnitude of the force P that is required to maintain…

Q: Q4/ The jib crane is supported by a pin at C and rod AB. If the load has a mass of 3 Mg with its…

A:

Q: Q2/. The automobile has a mass of 1 Mg and center of mass at G. Determine the towing force F…

A: Consider the below FBD for calculation: Based on the data given in question, m = 1 Mg = 1000 kgW =…

Q: F3 = 0.5 kN Z 45° (-1.5 m, 3 m, 3 m) F₂ = 0.75 kN 120° 60° F₁ = 2 kN -y

A:

Q: Q-3: The rod supports a cylinder of mass 160 kg and is pinned at its end B. If it is also subjected…

A:

Q: The piston C moves vertically between the two smooth walls. If the spring has a stiffness of k = 12…

A: The spring constant, k = 12 lb/inThe spring unstretched when θ = 0°The final angle is: θ = 20°

Q: Problem Statement Based on Problem 6-11 from the textbook. The spring has an unstretched length of…

A:

Q: The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position as…

A: Given :unstretched length of spring AB is 3 mFrom the figure , the stretched length of spring AB LAB…

Q: Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power…

A: Given data To determine tesnion T in the belt and reactions at C and D in different directions when…

Q: The disk B has a mass of 20 kg and is supported on the smooth cylindrical surface by a spring with…

A:

Q: Determine the tension developed in wire CA required for the equilibrium of the 11 kg cylinder. Take…

A: Equilibrium: In mechanics, equilibrium refers to a state of balance where the net force and moment…

Q: Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power…

A:

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: Based on Problem 5-87 from the textbook. Both pulleys are fixed to the shaft and as the shaft turns…

A:

Q: Determine the magnitude of the reaction in the pin A, the cable BC and the cable that supports the…

A: Given Data To find1) Ay1 Ax2) T

Q: The mass center G of the 1220-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: 3–18. If the spring DB has an unstretched length of 2 m, determine the stiffness of the spring to…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Determine the tension in each cable necessary for equilibrium of the massless pipe supporting 800…

A: Uniform load applied on pipe:Total length of the uniform load:And structure is symmetric about XZ…

Q: Determine the stretch of each spring for equilibrium of the 20-kg cylinder. Complete solutions must…

A: Given data:The mass of the cylinder  Determine:The stretch of each spring

Q: Each spring has an unstretched length of 2 in and a stiffness of fc = 330 N/m . 1. Determine the…

A: The unstretched length is l=2 in. The spring constant is fc=330 N/m

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.