Problem 20-7A pair of worm and worm wheel is designated as(2/40/10/4). The input power to the worm is 5 kW. Thepressure angle is 20°.The worm wheel is mounted between two bearings A andB. It can be assumed that bearing B takes complete thrustload. Determine the reactions at the two bearings.720 rpmAB60 mm130 mm

Answered: Image /qna-images/answer/ca19bd35-c1ab-4fc0-a647-f7b828ce8d86.jpg

Answered: Determine the reactions at the two…

Engineering

Mechanical Engineering

Determine the reactions at the two bearings.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
Hello, Could you please help with the question attached or give guidance please, thnk you
Hi, could you please help with the following question please thank you
The equation of the turning moment diagram for the three crank engine is given by: T(N.m) =25000 - 7500 sin 3theta where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb.
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley.
The firing order in a 6-cylinder vertical 4-stroke inline the engine is 1-2-4-6-5-3. The piston stroke is 100 mm and length of connecting red is 200 mm. The pitch-distance between cylinder center lines are 100 mm, 100 mm, 150 mm, 100 mm and 100 mm respectively. The reciprocating mass perlylinder is 1.0 kg and the engine runs at 3000 rpm. Determine the unbalance primary, and secondary forces and couples on engine. Is it the best firing order? If yes, why? What will be consequence of other firing order.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
The figure shows a 16T 20' straight bevel pinion driving a 32T gear, and the location of the bearing centerlines. Pinion shaft a receives 2.5 hp at 243 rev/min. Determine the bearing reactions at A and B if A is to take both radial and thrust loads.
Draw free-body diagrams of the two gears, assuming an input couple M on theOUT X shaft of the larger gear in the direction shown. Include forces at bearings A, B, D and E. M isthe reaction couple at the output shaft - i.e. the resistance to turning of the object being driven.The gears have 48 and 24 teeth respectively. If the input gear (large gear) turns at 100 rpm(= revolutions per minute), the output speed (small gear) is _______rpm.Wil OUT X IN Xl M be larger or smaller than M ?
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the hp requirement to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8, and is 3D printed such that it has a yield strength in shear of τy = 2500 psi. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3. Note that circular tooth thickness, t, at the pitch circle is π / (2P). Repeat for a gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20 ksi). Only do the part for the 6061 gear do not do it for the 3D printed gear