Determine the reactions at the support A, B and C using force method. El is constant. ㅏ 12ft B. Note: Consider the "By" as the redundant reaction 12 ft- 3 kip/ft

Q: 12 KN/m A Solve for the moment.

A:

Q: 294

A:

Q: AR Зм J 4 m w= 15 k/m Эм

A:

Q: Determine the hydrologic risk

A:

Q: The moment reaction (in kN.m) at the fixed end A for the frame in the figure :below is 6 kN d1=6.1…

A:

Q: For the frame loaded as shown, draw the complete and correct FBDs of the following: whole frame,…

A:

Q: The beam is supported by hinged and roller at A, B, C, D and E. Determine the reaction at the…

A:

Q: Qus Determine the reaction at the support. Take R 37

A: Given data : R = 37 k/ft A problem of Structure.

Q: find the reaction of the wall at A on the lower shaft

A: balancing the two spheres first draw free body diagram of both sphere seperatly

Q: - Reaction at A, shear at section 1---1, and moment at C. by using muller breslau principle. Write…

A: Muller Breslau principle it uses influence line diagram

Q: Give the horizontal reaction also

A:

Q: Determine the horizontal component of reaction and the vertical component of reaction at D. Also…

A: Given : P1 = 9 kN and P2 = 17 kN Determine the horizontal and vertical component of reaction at D ?

Q: E A В C -8 m- -8 m- -5 m- -5 m-

A:

Q: 25. What is the reaction at 20 kNím 60AN support B? 120 AN - m 26. What is the maximum shear force?…

A:

Q: Determine the reaction at B using the moment-area theorem and draw the bending moment diagram. Mo B…

A: Need to determine the Reaction at B and Bending Moment Diagram

Q: Determine the reactions at B, C, and the maximum force F if the reaction at A is 175 kN. Note that…

A: To find Reaction at B &C  Maximum force F

Q: 3000 lb 40° 4 ft B 6 ft A D 8 ft

A:

Q: From the given beam: Calculate the reaction at point B. If the concentrated force is equal to 40…

A:

Q: Situation #7 Use the cantilever method and determine (approximate the reactions at supports A and B.…

A:

Q: Determine the Resultant Force of the Uniformly Distributed Load shown in figure below, and draw its…

A: Consider the figure,

Q: Determine the reactions in the following beam with El constant and solve them using the stiffness…

A:

Q: 1 kN/m, a live load of 2 kN/m, and a concentrated live load of 52 kN. Determine the following:…

A:

Q: Beam ABCD carries a varying load on segment AB as shown below and a counter clockwise couple at…

A: Find reaction at A

Q: A Į - 6 m W B ·20

A:

Q: 25 KN 30 KN/m A 5 I 2 m 2 m B

A:

Q: -3 ft- 100 lb 3 ft- B 200 lb-f 2 ft 13 12. B 15 Determine the reactions on the bent rod which is…

A:

Q: 100 kN 10 kN/m A 12 m 6 m 21

A:

Q: Determine the reactions on the bent rod which is supported by a smooth surface at B and by a collar…

A: Given :

Q: A continuous beam carries the following loads. 12 kN/m 20 kN A 4m 3m 3m 1. Compute the moment at A…

A:

Q: 30KN/m sokwlm Zim 3m im 4m

A: Given data in question  Simply supported beam  UVL UDL Span member length  To find out  Reactions…

Q: b

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: (a)Determine the resulting moment at point A when the value of F=30lb and G=75lb. (b)Determine the…

A: A loaded beam is given and it has been asked to determine support reactions at A. Please refer step…

Q: Find the reaction R.

A: Bending Moment Diagram (BMD) : The moment at B due to reaction R1 = R1L The moment at B due to UDL…

Q: Determine the reaction at support B using Force method analysis. Assume support A is fixed and…

A:

Q: МА RA 20 KN 20 KN MB KAB = 10.67x10⁹ -3m-xl-3m-x-3m-²4 m. RB 60 KN KBC = 9x10⁹ in-de 4 m. a.…

A: Given: A beam with loadings on it Required : Moment distribution table  Moment at A, B and C…

Q: 2. Determine the components of the reactions of roller at B and hinge at C. 120 lb 6.5 in.- 4.5 in.-…

A:

Q: 9-10. Determine the reactions at the supports, then draw the moment diagram. Assume B and C are…

A: Support B settles by 30 mm Modulus of elasticity= 200Gpa

Q: Determine the reactions in the following beam with El constant and solve them using the stiffness…

A:

Q: Determine the moment reaction at A of the given indeterminate frame below. -15 ft 15 ft В 15 ft 4…

A:

Q: 10 ft- A -10 ft. C -10 ft- B -5 ft-

A:

Q: Determine reaction at supports B

A: Given data : uniformly distributed load=wTotal length=LMoment of inertia=IModulus of…

Q: Determine the reaction at A,C and D.

A: reaction at A , B and D

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.