Determine the reactions at A and C. *

Q: Q1. Determine the reactions at A, B, C, D of fig. * B

A:

Q: determine the value of the reactions  RA= RFY/RFX=

A:

Q: Determine the reactions at A and B when: ( a) α-0 (b) a = 75° (c) a = 35°. 75 lb 10 in. 10 in. В a…

A: Find the reaction at A and B

Q: Determine the reaction at A & B 40 b 10 in. 30 20 in.

A:

Q: Detemine the reaction a A, B and D tokN

A:

Q: How about this part :"Determine the x and y components of reaction the pin C exerts on member EDC…

A: F1 = 8 KN

Q: 2 kN/m 2 m 10 kN 4 m 2 m 5m

A: Determine the point load corresponding to the point load. W=2 kN/m·5 m=10 kN So a point load of 10…

Q: Problem 2 Determine the reactions at 0 for applied force F = 100 i – 50 J N. %3D 150 mm 200 mm 250…

A:

Q: .Q1 Determine the reactions at point A, in the below figure 0.9 m 70 N 65 20 N.m -03m- -0.7 m-

A: It is required to determine reaction at point A

Q: R=0.8m

A: Given

Q: Determine the reaction At C

A:

Q: tokN 6m 100KN TTT 4m 6M

A: Given: A truss is subjected to a loading as shown in the given figure. Determine: Determine…

Q: Determine the reactions at the roller B, the rocker C, and where the beam contacts the smooth plane…

A:

Q: 3. For the frame shown, draw the FBD and determine the reactions at A and C D 200 N 450 mm 200 mm в…

A: F=200 N

Q: Determine the horizontal and vertical components of reaction at C.  P = 345 N

A:

Q: H.W/: Draw (F.B.D) for the system and determine the reactions at point A as shown in figure The body…

A: Draw the given diagram for the problem. RV Resolve the 6 kN force in horizontal and vertical…

Q: Principle of superposition to determine the reactions at the supports A and B.EI is constant

A:

Q: Determine the reactions at A and E if P = 920 N. The reactions are positive if to the right or up,…

A:

Q: 625 N /m 400 N /m A B 2.5 m 6 m

A: Given Data The uniform distributed load acting on the beam is 400 N/m.  The uniform varying load…

Q: Q3. Determine the reactions at the pin ( A ) and the roller ( B) 80N 150 N A 44 FON 10ON

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: Determine the reaction at A on the beam. Let wo = 97 kN/m, L= 3 m.

A:

Q: Determine the reactions at the Smooth contact points A,B and C 250 N 30 30 0.15 m 0.2 m

A: Apply Static equilibrium to solve this problem

Q: Solve for the reactions at A.

A:

Q: Determine the reactions at supports A, B and C 10KN Hinge 3kN 2kN.mg 6kN D 2 m 3 m 2 m 4 m 2 m 幸 幸

A: The hinge support at A gives the horizontal and vertical reaction The roller support at B and C…

Q: 1. Determine the reactions at A and C. 2m B 1.8 m 3m CA15 kN/m 12 kN/m-

A:

Q: Determine the reactions at B when angle alpha is 50°. *

A: Assume that the mass of the strut is negligible. The system has co-planar, non-concurrent forces…

Q: Determine the reaction A, B, C, D and E in kn

A: Given data  Given force system

Q: Note: All systems are in equilibrium. 1.) What are the reactions at A and C for member ACD? The…

A:

Q: The beam is subjected to the concentrated force shown in Fig. a. Determine the reactions at the…

A: The downward deflection at the point B due the applied load must be equal to the upward deflection…

Q: Determine the components of reaction at C. Take that P = 420 N .*

A:

Q: Determine the reactions at A and B when β= 80°.

A: The free body diagram of the beam is given below,

Q: 4- Determine the reactions at the support A.

A:

Q: The shaft is supported by three smooth journal bearings at A, B, and C. Determine the components of…

A: Given : system consists of forces applied in different directions supported by journal bearings.Find…

Q: · Determine the reactions at A and B. 6 kN/m -3 m -6 m-

A: Draw the free-body diagram of the beam.

Q: Determine the reactions at B and D when b = 55 mm.

A:

Q: Determine the value of a for which the magnitude of the reaction at B is equal to 800 N.

A: Given Data: The reaction at point B is, RB=800 N Draw the free body diagram of the frame with all…

Q: Determine the reactions at B when b = 60 mm.

A: The member CD has two force members, the line of action of reaction at D must pass through points C…

Q: Determine the reactions on member ABCD at A, C, and D.

A: Please find the answer below

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.