Determine the reactions at A and B for the beam subjected to the couples and distributed load. At x = 0, the distributed load isincreasing at the rate of 9 lb/ft per foot.Assume a = 3 ft, b = 21 ft, w₁ = 230 lb/ft, w₂ = 550 lb/ft, M₁ = 2940 lb-ft, M₂ = 1390 lb-ft.M₁Answers:A =iB = iW,w|I1w = ko+k₁x + ₂x²AbTBlblbW₂M₂

A simply supported beam with supports at A and B, are applied with two couples and varying loads M1…

Determine the reactions at A and B for the beam subjected to the couples and distributed load. At x = 0, the distributed load increasing at the rate of 9 lb/ft per foot. Assume a = 3 ft, b = 21 ft, w₁ = 230 lb/ft, w₂ = 550 lb/ft, M₁ = 2940 lb-ft, M₂2 = 1390 lb-ft. W w 1 I w = k₁+k₁x + ₂x² A B O W₂ M₂

Determine the reactions at A and B for the beam subjected to the couples and distributed load. At x = 0, the distributed load increasing at the rate of 9 lb/ft per foot. Assume a = 3 ft, b = 21 ft, w₁ = 230 lb/ft, w₂ = 550 lb/ft, M₁ = 2940 lb-ft, M₂2 = 1390 lb-ft. W w 1 I w = k₁+k₁x + ₂x² A B O W₂ M₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is supported as shown below: Hing A E B D 1m 1m 1m 1m The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: w(DL) w(LL) P(LL) 30 15 50 Determine the following: 1. Maximum reaction at A, RA in kN.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 11 mm and a length of L1 = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 21 mm and a length of L2 = 0.8 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 76 kN is applied to the rigid bar.
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where M0 = 1,220 N-m, P = 2650 N, w0 = 1702 N/m, a = 2 m, b = 1.5 m, c = 3.5 m, d = 1.5 m
The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length of 2m. If it is subjected to two torques 500 N.m clockwise, positioned 0.3 m from the support A and 800 N.m counterclockwise positioned 0.2 m from the support D. Determine the reactions at fixed supports A and D. Express your final answers in N.m.
3 m 3 kN/m B 3 m C 5 kN 1.5 m 1.5 m D The beam has an internal hinge at C. Express your answers in kN. Solve for the reaction at A.
Use X = 137 Y = 37 A = 6 B = 8 C = 1
Determine the reactions at the supports of the beam. Assume that support at B is a roller and EI is constant. 8ft What is Ay in Lbs? 75 Select the correct response: 38.7 200 19.35 B
Find roller support reaction
Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. 4.0 m po Answers: BC= A 4.0 m BE = EF= i i i B 4.0 m 4.0 m 2.5 m E 12.5 KN 4.0 m kN 2 2 2 kN kN D
Q3/ The force P is applied to (a) the 60-lb block and (b) the 100-lb block. For each case, determine the magnitude of P required to H, = 0.40- 60 lb P (a) initiate motion. -->P (b) H, = 0,12- 100 lb
9
X=193 Y=93 A=2 B=7 C=9