Determine the reaction at B, C and E 10 k 20 k Rk 1/

Q: A two bay Vierendeel Girder has a bay width and height L= 4.8 m. It supports a single point load of…

A: step 1-

Q: press eases the volume of Find the b percent. lasticity of the liq

A:

Q: A reservoir is filled with 4 m of water. A pump of area 0.009 m² at the bottom of the reservoir is…

A: ###Determination of flow rate Q through pump ##

Q: Question 11 Construct the Shear and Moment diagrams COMPLETELY. Indicate all the abrupt change in…

A: A loaded beam is given and it has been asked to determine support reactions and shear force and…

Q: Y-Y 2) Dr = (x100%) Y -Y, max

A: Solution Relative density for cohesionless soil Dr=emax-eemax-eminWheree→emin ( Densest state)…

Q: Consider the following data for concrete with mild exposure Water-cement ratio = 0.50 Water = 191.6…

A: Given data- Water cement ratio=0.50, Water = 191.6 litres, To Find- The cement content.

Q: horizontal point load of 5 kN at point D. Determine the shear force and axial thrust at point E.

A: Shear force: - It is a force whose direction is parallel to cross section of body.

Q: A simply supported beam with a span of 9.5m has a uniformly distributed dead load (including the…

A: step 1-

Q: A column is supported on a footing as shown in the figure below. The water table is at a depth of 10…

A: Given- Water table at a depth of 10 m, Size of footing- 1.5 m × 3 m, Depth of footing Df=1 m, Unit…

Q: Show that the vectors ( A=3i+ 6j) and ( B=-i-2j) have opposite direction

A:

Q: Liquid is flowing in a pipeline 60 mm in diameter at 9.5 cu. m. per hour. If the density of fluid is…

A:

Q: 13- How many bbl does a 8000ft of 5x4 (OD-ID) drill pipes displace?

A: Given h = 8000ft Outer dia = 5ft  Inner dia= 4ft

Q: Calculate the Midspan Deflection of the Beam using Double Integration Method (Macaulay's METHOD…

A: Calculation of Mid Span Deflection using Macaulay Method

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: Answer To calculate the maximum flexural stress in tension and compression we have Bending equation…

Q: i Given the four points A (1, -1), B (2, 0), C (-1, 3) and D (-2, 2) Find the vectors AB and CD and…

A:

Q: A rectangular beam 300 x 600 mm cross section is subjected to bending moment of 50 kNm. The tension…

A: Given: A rectangular beam 300×600 mm cross section. Subjected to bending moment of 50 kNm. The…

Q: A 160-lb box is held at rest on a smooth surface (9 = 19°) inclined by a force, 'P' making an angle…

A: This question is related to the Engineering Mechanics from Civil Engineering. In this problem we…

Q: Question- A water treatment plant is to treat water at the rate of 6000 m³/day. If there are two…

A: Detention time (t) t = (Volume of tank) / ( Rate of flow through the tank) t= V/Q Volume of one tank…

Q: Example21 A vibrating system of mass 20 kg and spring with stiffness 32 N/mm is viscosity damped so…

A:

Q: Calculate the limiting length (m) of the offset, if the maximum allowable error in laying offset is…

A: given- maximum allowable error=2oscale of map= 1 cm = 100 m

Q: Determine the maximum deflection in region AB of the overhang beam. Take E = 29(103)kst and I =…

A:

Q: Member (1) has an area of 2300 mm? and an allowable normal stress of 110 MPa. Member (2) has an area…

A: Lami's theorem: when three forces acting on the body where the forces are coplanar and concurrent,…

Q: Fluid Properties A hydraulic lift consists of a 40 cm diameter ram and slides in a cylinder of…

A:

Q: The end of the boom O is subjected to three concurrent and coplanar forces. Determine the magnitude…

A: Schematic diagram of the given problem:

Q: Question 22 B, Hydrology- Over a basin of area 333 km², there was a storm for 6 h with a uniform…

A:

Q: The service loads acting on a structural member are as follows: DL = 80 kN/m; WL = 50 kN/m; LL = 40…

A: Given data, To find the limit state of collapse load

Q: 1. Some geophysical (dynamic) tests were performed in the field on a rock layer, and the velocity of…

A: Given Data:γ = 2600 kg/m3= 25506 N/m3Velocity of shear waves, Vs=1000m/sVelocity of primary waves,…

Q: 6. A cylindrical sample of soil is iso-tropically compressed at 150 KPa under drained condition.…

A: A sample is compressed at 150 kpa at under drained condition and change in radial stress 300 kpa and…

Q: A basin has an area of 400 km² and the following characteristics: L = Basin length = 35 km Le =…

A:

Q: Find the force in member HG and specify if it is in tension or compression? HG = 4 kN 3 kN 2 kN E 3…

A:

Q: A sample saturated cohesion less soil tested in a drained triaxial compression test showed an angle…

A: A sample of saturated Cohesion less soil So, C=0,Angle of Internal friction Confining pressure To…

Q: Determine the expected dragline production in loose cubic meters (LCM) per hour based on the…

A:

Q: Determine the LRFD design strength (kN) of the compression member shown. The distance between the…

A:

Q: Problem 1. The beam cross sections shown (A and B) have #3 stirrups spaced at 8 inches on center.…

A:

Q: Note: Please show all of the free body diagrams used (from reactions and etc.) and also show the…

A:

Q: A concentrated vertical load of 3000 kN is applied depths 1 m and 2 m below the ground, respectively…

A:

Q: Three simple structures (two are trusses) are shown below. Use the method of joints (solve…

A:

Q: A vertical sag parabolic curve connects a -6% grade to a +1% that meets at station 12+720 with an…

A:

Q: Required information A certain location on a structure has the following stress element: 35 MPa Txy…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.