Determine the radius of a taxiway for a supersonic aircraft to negotiate the curve at a turning speed of 60 kmph. The wheel base is 35 m and the tread of main landing gear is 7.5 m. The airport is of type 'A' as per ICAO. Assume coefficient of friction between tyre and pavement surface as 0.15.

Determine the radius of a taxiway for a supersonic aircraft to negotiate the curve at a turning speed of 60 kmph. The wheel base is 35 m and the tread of main landing gear is 7.5 m. The airport is of type 'A' as per ICAO. Assume coefficient of friction between tyre and pavement surface as 0.15.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A ASHOK LEYLAND REQUIRED TO ACCELERATE AT A RATE OF 2 /SEC 2 IN THE FIRST GEAR FROM A SPEED OF 15 K.P.H THE GRADIENT IS + 3 PERCENTAGE AND THE ROAD HAS A BLACK TOPPED THE FRONTAL PROJECTION AREA OF THE CAR IS 3.0 M2.THE CAR TYRES HAVE A RADIUS OF 0.50 M. THE REAL AXLE GEAR RATIO IS 3.82 :1 AND THE FIRST GEAR RATIO IS 478 :1.CALCULATE THE ENGINE HORSEPOWER NEEDED AND THE SPEED OF ENGINE. ASSUMING F= 0.04, TRANSMISSION EFFICIENCY OF 0.80, TYRE DEFORMATION FACTOR = 0.85, RO=0.60
4. A building is located 8.8 m from the centerline of the inside lane of a curved section of highway whose radius is 145 m. the road is level and e is equal to 0.10. Determine the maximum possible posted speed limit (to the nearest 5 km/h) assuming that the coefficients of longitudinal and side friction are equal to 0.35 and 0.13, respectively.
A car is traveling at a speed of 100 ft/s which accelerates 12 ft/s2. The perception reaction time for the driver is 2.40 s. If the maximum grade of the road is -3.7%, compute the following: a. Braking distance in meters b. Lag distance in meters
A car requires 4m to stop after the application of brakes. Determine the speed of the car just before the brakes were applied. The road has a slope of -2.4% and average of coefficient of friction of 0.42.
A car travels around a curve with a radius of curvature of 60 meters. If the coefficient of friction is 0.2, what must be the banking angle of the curve so that so that the frictional resistance is zero?
. The design speed on a road is 60 kmph. Assuming the driver reaction time of 2.5 seconds and coefficient of friction of pavement surface as 0.35, the required slopping distance for two-way traffic on a single lane road is
A road is passing through a hilly area with horizontal curve.If the superelevation provided is 1 in 10 and the coefficient of lateral friction is 0.16, the minimum radius of the horizontal curve which the vehicles can negotiate safety at a speed of 40 kmph in metres is
Need within 1hr please, thanks A 0.5 kg block slides on a circular road with a radius of 4 m in the vertical plane. Block speed is 4m/s as it passes point A and 5 m/s passes point B. Angle distance from point A and B is 30 along the radius. Determine normal force exerted on block by the surface at point A and B and the total acceleration at Point B.
3. A building is located 8.8 m from the centerline of the inside lane of a curved section of highway whose radius is 145 m. the road is level and e is equal to 0.10. Determine the maximum possible design speed. Assume the longitudinal and lateral coefficients of friction are equal to 0.35 and 0.13, respectively. Ensure you check speed for both stopping sight distance and vehicle stability. Assume a standard perception-reaction time of 2.5sec.
The rated speed of a highway curve of 60m. radius is 50Kph. If the coefficient of friction between the tires and the road is 0.60, What is the maximum speed at which a car can round the curve without skidding?