Determine the planar density for FCC nickel in the (111) plane with lattice parameters of ao=3.5187. O 1.6*10¹5 atoms/cm² 1.1*1015 atoms/cm² 1.9*1015 atoms/cm²

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: Referring to the figure, calculate for the following:a) Component of the 800 N force in the…

A: Step 1: Step 2: Step 3: Step 4:

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: I need answers for problems 1, 2, and 3 pertaining to the print provided.

A: (1). Yes, the detail drawing is of a single part namely the Bonnet Sleeve.

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: what happened with the 10 in the first equation?

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: The diagram shows a 1 cm3 block that is divided into cubic millimetres. How many mm are there along…

A:

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: Define the term work of force?

A: Work of force is defined as the dot product of force and displacement  W=F.S…

Q: can this be done using simpsons rule?

A: As already calculated using the relation    for the volume ranging from to  in steps of , the…

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

The Space Lattice and Unit Cells

Every matter consists of atoms, molecules, and ions. If these atoms, molecules, and ions (micro-particles) are represented in a three-dimensional space-occupying certain specific points in space, then these arrangements are termed as space lattices and the specific points which are being occupied by atoms, molecules and ions are termed as lattice points. The atoms, molecules, and ions at the lattice points are generally grouped in a regular fashion and repeat periodically at the three-dimensional space.