Answered: Determine the normal and shearing…

Determine the normal and shearing stresses after the element shown has been rotated through 50° clockwise, using Mohr's circle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Part B The state of stress at a point is shown on the element. Take σ₂ = -15 ksi. Determine the…

A: For the solution refer below images.

Q: 3. Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at…

A: Given Data Dimensions of the beam are 4in×3in Area, A=4(3)=12 in2 Moment of inertia, I=3(4)312=16…

Q: Determine the orientation that causes normal stress to be a maximum?

A: Understand that the normal stress is maximum at the major principal plane. Therefore, to determine…

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Given:σx=50 MPaσy=-30 MPaζxy=20 MPa

Q: 4 ksi The state of plane stress at a point is shown on the element. (a) Draw Mohr's circle neatly to…

Q: Required information Consider the given state of stress. Given: X= 5 ksi and Y= 25 ks + + 6 ksi The…

A: The value are

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A: Consider below figure for the given question: We are given, Load = P = 2000 lb Diameter of pulley =…

Q: Draw and stress tensonr with the following characteristics The stress cube visualization at point…

Q: 1. For the given state of stress, determine (a) the principal planes, (b) the principal stresses.

Q: For the given state of stress, determine the planes with compressive normal stress equal to 15 MPa.…

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: 2: haft shown below, determine the normal and A, including stress concentrations. Then dr and…

A: Given: r=0.0042 m d=0.03 m D=0.033 m P=1500 N M=300 Nm T=250 Nm

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are ox= 30…

A: Given: The stress on the x phase is σx=30 MPa The stress on the y phase is σy=-25 MPa The shear…

Q: A cylindrical rod .5" in diameter is subjected to an axial load of 11,300 lbs. A square bar of .5"…

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

Q: How is the state of plane stress at the point uniquely represented?

A: If the stress state at a material particle is such that the only non-zero stress components act in…

Q: Determine the equivalent state of stress on an element at the same Sig1 point which represents (a)…

Q: Draw Mohr's circle that describes each of the following states of stress.

A: Given data:- σx =-8 ksi σy =12 ksi τxv=-6 ksi To draw:- Mohrs circle

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

!
Required information
Consider the given state of stress.
+
A 60 MPa
20 MPa
The shear stress Tx'y'is -
Determine the normal and shearing stresses after the element shown has been rotated through 50° clockwise, using Mohr's circle.
The normal stress ox'is -
32.3
MPa and oy'is 52.3 MPa.
40 MPa
17.6
MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Find the average normal stress. 2. Find the maximum in-plane shear stress.
solve, show all steps/solutions. include all asked for, no partial answer or ill dislike
Answer both parts please! Part A. if the bolt is subjected to a compressive force of P= 21.3 kN, deteemine the magnitude of the average normal stress in the steel. Part B. if the bolt is subjected to a compressive force of P= 21.3 kN, determine the magnitude of the average normal stress in the bronze.
What steps should be taken to obtain The resultant internal loadings at a point located on the section of a body using the method of sections?
The solid rod shown in the figure below has radius of 0.63 in. If it is subjected to the force of 765 Ib, determine the state of stress at point A using superposition. C 8 in. 10 in. 765 lb 15 in. B
Illistrate Mohr's circle for the given plane stress state. Including the coordinates of the points, show the points with the faces of the figure, the center of the circle and the magnitude of the radius. 7. 3kPa 5kPa 1kPa
Required information Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a diameter of 0.8 in. Take P = 2300 lb. B 2.5 in. 600 lb 1 in. The principal stresses are: ksi A Determine the principal stresses and the maximum shearing stress at point H. (Round the final answers to two decimal places. Input the answers with the appropriate sign.) 3.5 in. max omin = ksi The maximum shearing stress is ksi.
The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given as shown in the picture below.Draw Mohr's circle.
Question 2. The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and moment produced by a 3 kN force which is 15 mm from the centre of the shafts cross section. The shafts have the same centroid. a. Using Mohr's circle, determine the principal stress, maximum in-plane shear stress and average normal stress in the at point J and K. b. If the weld has a 30° at point J, what is the maximum shear stress the weld has to with- stand. K 700 mm F=3kN 15 mm c. Determine the maximum bending stress if the hole in the cross section area is now off centre by 2 mm in the x and y direction.
Determine the maximum shearing stress in a bronze helical spring composed of 19 turns of 0.96-in.-diameter wire on a mean radius of 3.53 in. when the spring is supporting a load of 516 Ib. Use the equation for heavy spring and G = 6 x 10° psi. (Answer must be in Ib per square inch) Round your answer to 2 decimal places. Add your answer
The 3/4-in.-diameter shaft is subjected to the loading shown. Determine the stress components at point A. Sketch the results on a volume element located at this point. The journal bearing at C can exert only force components Cyand Cz on the shaft, and the thrust bearing at D can exert force components Dx, Dy, and Dz on the shaft.
Two wood members of uniform cross section are joined using a simple glued scarf splice. Determine the normal and shearing stresses in the glued splice. The column is loaded in tension through the centroid with the load indicated. 2.4 kip 6" 60° 2.4 kip