Determine the moment of inertia of the shaded area about x-axis. Set h= 38 cm and r= 8 cm. h 1.5h - 1.5h 16288517 cm 16615141 cm4 16618358 cm4 4070871 cm4 15961892 cm

Q: b. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility = c. Number of…

A: In these drawn mechanism, we need to find the number of lower pairs (binary joints) and higher…

Q: Using the image on the Moment of Inertia Tab, where the following criteria are considered: Assign…

A: The moment of inertia tab is given. The torque applied is given as, T=2 N-m

Q: (3) Use the following graph to answer the questions on this page. The total time is 0.4 seconds.…

A: Solution:

Q: Part B Find M, the magnitude of the moment, and 0, the angle between r and the force F.

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: A BMW vehicle consumes 2.5 gallons of gasoline in 60 minutes while operating at3000 RPM. Calculate…

A: Given:The BMW vehicle consumes  gallons of gasoline in  minutes.Each gallon of gasoline contains  of…

Q: 5. I went for a 2 mile bike ride. With the given information below, how many times did I pedal my…

A: Distance to cover S = 2 mile = 2 x 63360 inch = 126720 inPedal crank radius rp = 4.6 in , so…

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: Help!! Please answer this correctly

A: Step 1: Step 2: Step 3: Step 4:

Q: An airplane flies at 28.9 m/s. The engine thrust exactly balances the drag force, which is 7.3 N.…

A:

Q: 5. Use calculus to explain why the rotation velocity of a point on the perimeter of a wheel is the…

A: In this problem, it is asking for only part (5) so we will answer only part (5).

Q: A particle travels along the circular path from A to B in 1 s. If it takes 3 s for it to go from A…

A: The average velocity of an item is its displacement over time. To calculate an object's average…

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: a) The length of the arms of a Porter governor is 300mm long. The upper and lower 10 arms are…

A:

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: The posltion of a particle is r = { (3t° - 2t)i - (4t"2 + t)j + (3f° - 2)k} m, where t is in…

A: Given, r→=(3t3-2t)i-(4t1/2+t)j+(3t2-2)k

Q: here is the pronblem with the solution but i dont know how the steps to solve it . pleasde help

A: The question in the image is a statics problem about a crank assembly subjected to forces. We can…

Q: A particle is moving along a straight line such that its position from a fixed point is s = (12 -…

A: Write the equation for the position of the particle. s=12-15t2+5t3 m Here, s is the position of the…

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Q: 5. The acceleration of a particle as it moves along a straight line is given by a = (2t - 1) m/s",…

A: Given Acceleration equation a = (2t-1) m/s2 Condition s = 1 m v = 2 m/s t = 0 s Time t = 6 s To find…

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.