Answered: Determine the moment of inertia of the…

Determine the moment of inertia of the cross-sectional area of the reinforced channel about the x-axis Assume t = 1.8 in., a = 3.2 in., b = 2.6 in., c = 3.6 in. a +1 pita- Answer: Ix = i in.4 x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A= 2.9 in.2. Assume a = 3.50 ft and b=4.20 ft. If the normal stress in each member must not exceed 25 ksi, determine the maximum load Pmax that may be supported by the structure. D Answer: Pmax= i b B b kips
SAMPLE PROBLEM NO. 8 Determine the force in each member of the complex truss shown in the figure. Assume joints B, F, and D are on the same horizontal line. State whether the members are in tension or compression. 20 kN 1.2m B 450 450 0.9m 2.4m
2. The steel rod is stress-free before the axial loads P, = 150 kN and P, 90 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E = 200 GPa. A=D2000 mm2 A D900 mm2 A=D1200 mm2 B. C. D. 500 mm +250mm-+-350mm
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 2.3 in.2. Assume a = 4.25 ft and b = 5.10 ft. If the normal stress in each member must not exceed 55 ksi, determine the maximum load Pmax that may be supported by the structure. D Answer: Pmax= i b E b kips P
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The couple M=1.1 kN-m acts in a vertical plane and is applied to a beam oriented as shown. Determine the stress at point A 10 mm 40 mm The stress at point A is ( 10 mm 40 mm -10 mm 1,-1.894 x 10 mm 1,-0.614 x 10 mm +0.800 x 10 mm MPa.
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 4.75 ft and b = 5.70 ft. If the normal stress in each member must not exceed 60 ksi, determine the maximum load Pmax that may be supported by the structure. a D Answer: Pmax = i b B E b kips P
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.46 in., -0.20 in.). Assume a = 15 ft, b = 30 ft, c = 10 ft, and d = 20 ft. Determine the normal strain in each bar. A Answer: EAB EBC = i i P a (1) B με με X b (2) C d
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
2. Calculate the increase in stress in each segment of the compound bar if the temperature is increased by 80°F. Assume that the supports are Aluminum Steel unyielding and use the following data: A (in') E (psi) « (°F) 10 x 10 12.8 x 10 29 x 10 6.5 x 10 Aluminum 1.5 2.0 -10 in- 15 in.- Steel
4. A rigid block of having a weight M is suspended by symmetrically placed rods. Each copper rod has an area of 1200 sq.mm: E= 125,000 MPa and the allowable stress is 90 MPa. The steel rod has an area of 1500 sq.mm; E 220GPa; and the allowable stress is 120 Mpa. Determine the largest weight M which can be supported by the rods. 8c=8s Copper 160 mm Pc Ps Steel 240 mm TIT Pc ..initial level Tinal level Copper 160 mm
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←