-Determine the minimum length of a highway sag curve (based on SSD Criterion) that is designed to join a - 0.035 grade to a + 0.025 grade, if the design speed is 90 km/h. Assume a = 3.4 m/s2, t = 2.5 s. Untitled Question

-Determine the minimum length of a highway sag curve (based on SSD Criterion) that is designed to join a - 0.035 grade to a + 0.025 grade, if the design speed is 90 km/h. Assume a = 3.4 m/s2, t = 2.5 s. Untitled Question

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the minimum lenght of a crest vertical curve if the grades are +4% and -2%. Design speed is 112km/h. State assumptions used in solving this problem.
An equal tangent vertical curve is intended to connect grades of 3% and -3.2%. If this curve is to be a part of a highway designed with a speed limit of 70mph, determine the minimum length (ft) of the vertical curve. Use exact solution (do not use the table)
A specific jurisdiction requires a minimum grade of 0.46% to be reached within 19 m from highest/lowest point of a vertical curve. Calculate the corresponding maximum K value of the curve in this jurisdiction for drainage requirements.
Two-way two-lane highway with a design speed of 110km/hr has two grades of +2.5% & -1.5% connected with a vertical curve at station 121+20 of elevation 210.5m. Find the station & elevation of the turning point on the curve?
You are asked to design a horizontal curve for a four-lane road. The road has 12-ft lanes. Due to expensive excavation, it is determined that a maximum of 47 ft can be cleared from the road's centerline toward the inside lane to provide for stopping sight distance. If local guidelines dictate a maximum superelevation of 8%, what is the highest possible design speed for this curve?
An equal-tangent vertical curve is designed for the year 2030 for a design speed of 70 mi/h to connect grades G1 = 1.2% and G2 = - 2.1%. In 2030, vehicles have become smaller so that the driver's eye height is assumed to be 3.0 ft above the pavement and roadway objects are assumed to be 1.0 ft above the pavement surface. Compute the design curve length for the year 2030. A. 1178.02 В. 1032.09 C. 974.12 D. 980.25
Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed=60 mph, max superelevation=8% 2) The design/full superelevation, in %, is: O 7.2 O 7.4 O 7.6 O 7.8 O 8.0
Q\ on a certain highway section, a +2% grade meets a -8% at a point with an elevation of 50m. The symmetrical parabolic curve joining the two grades provide a safe driving speed of 120 km\hr. determine the elevation of the highest point on the pavement surface within this section? in Assume a=3.41lm\sec² , S
A two-lane highway is being expanded to four lanes with the original highway consisting of the northbound lanes and the new highway carrying the southbound lanes. At one location, the southbound facility crosses over an existing pipeline. The resulting vertical curve needs to be at least 10 feet above the top of the pipeline. The initial grade is -4 and G2 is +2. The design speed for the new highway is 60 mi/hr. (1) Is the length of the design curve greater or less than the required stopping distance? (2) The PVI is at station 425+74 and the elevation is 980 ft. If the pipeline is at station 424+54 and the elevation of the top of the pipeline is 985 ft, is the distance from the curve to the top of pipeline adequate to meet the 10 feet required cover? I recommend drawing the cross-section of the curve including the location of the pipeline when answering this question. Note that instead of clearance from the curve up to the the bottom of the overpass (example in the book), this is…
A crest vertical curve will connect a 1.5% grade to a -3% grade with a design speed of 45 mph. Using the SSD (stopping site distance) criterion, what is the minimum length of the curve?
As a roadway designer you are asked to design a horizontal curve for a two-lane road that are 12' wide each. There is an enormous boulder in the way of the construction zone and the minimum distance needed to excavate towards to the center must be solved for. The distance is required to sustain a speed of 55mph at a maximum super-elevation of 10%. Find the minimum distance from the boulder to the center of the road that fulfils the design requirement
A new highway is designed to join a crest curve with +1.0% and -0.5% grades for PVC and PVT, respectively. Knowing that the stations of PVC and PVI are STA 51+25 and STA 56+90, examine whether or not the curve is long enough to provide passing sight distance when the design speed is 60mi/h.