determine the maximum water temperature to avoid the danger of cavitation.

Q: 2-45 Saturated refrigerant-134a liquid at 10°C is cooled to 0°C at constant pressure. Using…

A:

Q: contains a fl gravity of 110 kN/ m² oil of specific der 1.30 anc pressure 170

A:

Q: Aliquid of density 900 kg/m³ rises to a height of 7 mm in a capillary tube of 2 mm Internal…

A: Density of the liquid, The angle of contact of the liquid in the glass, The diameter of the…

Q: The allowable Net Positive Suction Head (NPSH) for a pump provided by the manufacturer for a flow of…

A:

Q: 4-61. Oil flows into the mixing tank through pipe A at 0.05 m/s, and glycerin flows into the tank…

A: To find the average density-

Q: A siphon tube is useful for removing liquid from a tank. The silphon tube is first filed with…

A: Let us assume that surface of the water is at position B and the exit of the hose is at position C.…

Q: A closed container contains 3m high of kerosene (SG = 0.85), water, and 0.7m high of an unknown…

A:

Q: An open cylindrical tank contains two liquids with a specific gravities and depths as follows:…

A: Liquid 1 Specific gravity, S1 = 1.02 Depth, H1 =1.12m Liquid 2 Specific gravity, S2 = 1.02 Depth, H2…

Q: A rigid, insulated vessel is divided into two compartments connected by a valve. Initially, one…

A:

Q: 3,0 m 10.0 m Oil (sg=0.86) 50-mm OD -x 1.5-mm wall FIGURE 6.27 Problems 6.72 and 6.83. 25-mm…

A:

Q: Flow rate of a fluid (density = 1000 kg/m³) in a small diameter tube is 800 mm³/s. The length and…

A: Given:Density of the fluidρ=1000 Kg/m3DischargeQ=800 m3/sQ=800×10-9 m3/sLength of the tube(L)=2…

Q: 5. Pressure variation for compressible fluid is maximum for which kind of process? a) Isothermal b)…

A:

Q: Q2/A storage tank of a treatment water has a holding capacity of 750 m' up to an overflow point. The…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: Air at standard conditions enters the compressor shown below through a 2.4-in diameter pipe at 10…

A:

Q: Flow rate of a fluid (density = 1000kg/ m³) in a small diameter tube is 800 m³/ s. The length and…

A: Given- discharge Q=800 m3/s density ρ=1000 kg/m3 Length L= 2 m Diameter D=0.5 mm pressure drop = 2…

Q: A full scale agitation system that has a flat blade turbine impeller with six blade-disk is used in…

A: The volume of the scale down system is one-fourth of the large scale volume. The ratio of the volume…

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

A:

Q: A 1.5-ft³rigid tank contains saturated refrigerant-134 at 170 psia. Initially, 20 percent of the…

A:

Q: 3- The pump of waste water of concentration (1.5 mg/liter) treatment plant system is powered by a…

A: Given data: The pump of waste water of concentration is 1.5 mg/lit. The power is 15 kw. The…

Q: 2. A compressible air inside an instrument tube is flowing at 350 m/s at standard sea level. The…

A: For compressible fluid continuity equation is given by the following formula, ρ1A1V1=ρ2A2V2 Here…

Q: c) For the system shown in Figure 3.1, calculate (i) the volume flow rate of water from the nozzle…

A: To find (a)Q=? (b)Pa=?

Q: Home Work P.3.1 Two pipes A andB carrying water are connected by a connecting tube as shown in…

A: The figure is as shown

Q: 8. Which one of the follflowing is correct? a) the frictional resistance is always dependent on the…

A: To Determine Which one of the 4 given options are correct.

Q: Compute the capillary rise in mm of pure water at 10 Celsius expected in an 0.8 mm diameter tube.

A:

Q: Choose the correct answer 1- If the dynamic viscosity of a fluid is 0.5 poise and specific gravity…

A: Since the question number to be solved is not specified, the solution for Question 01 is as follows:…

Q: Flow rate of a fluid (density = 1000 kg/m³) in a small diameter tube is 800 mm³/s. The length and…

A:

Q: An le Volve Pump open P=150 kPa Water sprotruding entrance

A: Given data in question  Diameter of pipe Density of water Dynamic viscosity of water Length of pipe…

Q: Water in a 35-cm dia. has 62°F temperature and the discharge is measured as 0.3 m/s and the pressure…

A: Please refer the attached image for complete solution.THANK YOU.

Q: 6. Can the flow inside a nozzle be steady and uniform? a) yes b) never c) it can be steady but never…

A: Explanation :  This situation/statement can be judged by continuity equation. In that density, cross…

Q: What power will be required in kW if the water will be delivered to 1.5m above the pump?

A:

Hydrogen Energy

Energy is a quantity that cannot be defined, its existence can only be felt. In simple language, if a system possesses energy, it can do a specific kind of work. There are many forms of energy sources which people can use to obtain work. Solar energy, tidal energy, hydroelectric energy, geothermal energy, wind energy are some of the renewable energy sources which are primarily used for the production of electricity.