Determine the mass of each of the two identical cylinders if they cause a sag of s= 0.36 m when suspended from the rings at A andB. Note that s = 0 when the cylinders are removed. Supply the answer in kilograms.1.5 mSW2 mk = 100 N/m1 m-2 mwww.wwwwwww100 N/m

Determine the mass of each of the two identical cylinders if they cause a sag of s = 0.36 m when suspended fre B. Note that s = 0 when the cylinders are removed. Supply the answer in kilograms. 1.5m wwwwww. 2 m- £= 100 N/m 2 m wwwwww 100 N/m

Determine the mass of each of the two identical cylinders if they cause a sag of s = 0.36 m when suspended fre B. Note that s = 0 when the cylinders are removed. Supply the answer in kilograms. 1.5m wwwwww. 2 m- £= 100 N/m 2 m wwwwww 100 N/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The brake system in most cars makes use of a hydraulic system. This system consists of a fluid filled tube connected at each end to a piston. Assume that the piston attached to the brake pedal has a cross sectional area of 0.6 cm2 and the piston attached to the brake pad has a cross section area of 2.4 cm2. Determine the force at the brake pad, if you apply a force of 10 N to the piston attached to the brake pedal. Please show the formulae, the calculations, all the steps.
Questions b-d
The construction vehicle has a mass of [m1] Mg with a center of gravity G1. The stone in the bucket has a mass of [m2] with a center of gravity G2. c) Determine the total reaction NA on the wheels at A. d) Determine the force F in the hydraulic cylinder CD. There are two mechanical arms, one on each side of the bucket. 1.25 m 30 E 0.5 m 0.15 m 1.5 m 0.75 m -
Formula to be used: Where: Please take note! Calculating Pressure in a Static Fluid or P = pgh or P = yh p is the fluid's density (kg/m³ or lbm/ft³) g is the acceleration due to gravity y is the specific weight of the fluid (N/m³ or lbf/ft³) W is the weight of the fluid (N or lbf) A is the area of the bottom of the vessel containing the liquid (m² or ft²) h is the depth/height of the fluid (m or ft) P = P = 1248 h that will be used for the formula may be different from the given height of liquid in a problem. Refer to the sample problem below for clarification on this matter. Sample Problem For the dam shown on the right, find the pressure at point 20 feet below the surface of the water. Solution: Here, we will not use h = 40 ft since we are asked to compute the pressure at point 20 feet below the surface of the water. So, here is the appropriate approach to this problem. P = yh The specific weight of water is 62.4 lbf/ft³. lbf P = (62.4 ft3) (20 ft) lbf ft² 40 ft 20 ft
A body weighs 250 lb at the earth's surface. Determine c. The weight of the body on the moon's surface.
Problem 2 В A manometer was used to determine the pressure of the gas at B. Three fluids were used, two of which are made of liquid having specific gravities of 1.25 and 0.80 while the third is a gas with an unknown specific gravity. What is the pressure (in Pa) at B? The specific weight of water is 9,810 N/m³. 5 сm A 60° 6 ст S.G. = 1.25 4 сm S.G. = 0.80
A 61.0-kg survivor of a cruise line disaster rests atop a block of Styrofoam insulation, using it as a raft. The Styrofoam has dimensions 2.00 m ✕ 2.00 m ✕ 0.0870 m. The bottom 0.022 m of the raft is submerged. A. Write Newton's second law for the system in one dimension, using B for buoyancy, w for the weight of the survivor, and wr for the weight of the raft. (Set a = 0. Solve for Fy, the y-component of the net force. Let upward be the positive y-direction.) Fy = ( ) = 0 B. Calculate the numeric value for the buoyancy, B. (Seawater has density 1025 kg/m3. Enter the answer to at least the ones digit.) C. Using the value of B and the weight w of the survivor, calculate the weight wr of the Styrofoam. D. What is the density of the Styrofoam? E. What is the maximum buoyant force, corresponding to the raft being submerged up to its top surface? F. What total mass of survivors can the raft support?
Q1) Find the force Fon the bottom of the tank if : K=1.5 m, H= 6 m , D=5 m. Air Oil Mercury s.g=0.9 F
The pressure inside a competion grade tennis ball is 1.6 times higher than the atmospheric pressure. The diameter and wall thicknwess of the tennis is 66 mm and 2.8 mm, respectively. Considering the atmospheric pressure as 100,000 Pa, determine the stress in the tennis ball at rest. Express the result in MPa with 2 decimal points.
Plunger (weightless) Area is 0.003 m² piston mass 1000 kg , area of piston is 0.3 m² density of oil is 750 kg/m³ determine force on Plunger required for equilibrium
QV: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.
2. A closed tank mounted on a truck 6m long, 2.50m wide, and 2m high is transporting oil (SG=0.85) at 85% capacity. Determine the a. required horizontal acceleration to the left causing a pressure of 5 kPa at the front wall. b. total force acting on the side with greatest depth. c. If the force at "b" is increased by 30 kN, what will be the new horizontal acceleration?