Determine the magnitude resulting from the intensity of the electric field at point P directed by two point charges q₁ =5μC and (q2=-3 μC. See the image 50 cm 20 cm 40 cm q₁-3 μ

The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 1 V/cm. Determine the (i) amplitude of waveform Q (i) peak to peak value of waveform P. (ii)i frquency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. () Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (ii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =

Rectifier   determine the following show complete solution

Voltage Doubler Multiplier Solve manually the voltage and current in each capacitor and diode, determine also the Vo.

Electrical Engineering please solve this thank you The following values are given for a shocdley diode Vi (derel vollaye) • 0.025 V Is (Deverse salunalia cmal): 10X10A -15 Given voltaye eg ^: v(t) = 0.7+ 8 Vr cosut IA RL= 50 0 %3D Find avg. powen diipted in shochly diode € ay.power deliveud to load

1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!

A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1

1 what must be the dis tance between paint charge 94=26.0 MC and point charge 92 = -47.0 MC for the electrostatic force between them to have a magnitude of 5.70N ? %3D

The current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 ID

The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (ii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =