Determine the magnitude and coordinate direction angles of the force F acting on the support. The component of F in the x-y plane is 7 kN. * 30° 40° 7 kN 8080 N O 880 N O 88 N 8.08 N

Q: From the given beam shown, and at the given point C, determine the following: a. the internal normal…

A: Consider the section ACB,

Q: |8.00 kips Sketch a Free Body Diagram of a BY section of the truss that facilitates determination of…

A:

Q: Determine the moment of the force about point P, which is 3 directly below the y-axis as shown. As…

A: Given Data:F→=-3i^+8j^+5k^Position Vector r→ for point Pr→=0i^+4j^-3k^

Q: is constant. Use th 6 ft C

A:

Q: Determine the internal normal force, shear force, and bending moment at point A in the beam. Note…

A:

Q: Determine the bar force in CD, CH and GH if P = 50kN. Indicate if compression or tensio

A: Solution: Draw the Free Body Diagram of the truss Apply the equilibrium equation of the forces…

Q: What is the lateral deflection at joint E in mm?

A: A truss supported at hinged support at A and roller support at E, is loaded with vertical loading…

Q: uss. Each m A 300 mm². E= work. =

A:

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A: Given data in question  Diameter  Length Rigidity modulus = 12×106 psi Shear stress To find out  T0…

Q: Determine the moment of the force F about point P.Express the result as a Cartesian vector.

A: The position vectors are calculated as,

Q: 12. Two forces can be replaced by an aquivalent force R acting at point B on the beam. Determine the…

A: Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Q: 3. Determine the resultant of the force system in the figure. 450N 850 N 48° 350 N 55 500N

A:

Q: 2.21 The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a…

A:

Q: B a D F

A:

Q: Using Force Method The frame has constant EI. Load P acts at rigid joint B. a) Determine all…

A:

Q: Determine the internal normal force and shear force, and the bending moment in the beam at the…

A: Given  Beam with dimensions Force at B  To find Bending moment at cross section a-a

Q: Determine the internal normal force, shear force, and bending moment at point D. Take w = 150 N/m.

A:

Q: 4. Find the vector moment along AO due to the force, Fo and force, FB. FB = 5 kN F, = 7 kN 6 m 8 m 2…

A: Given :- Force FD and force FB are given  Magnitude of force FD = 7 KN  Magnitude of force FB = 5 KN…

Q: determine the slope at the left support A (in degrees). the beam is loaded with a moment load…

A: Find reactions:∑ MB=0RA9-18=0RA=2kNso,Moment diagram is shown as belowusing conjugate beam…

Q: Determine the magnitude of the pin force at C given θ = 23° and P = 52 lbs.

A: P = 52 lbs θ = 23o

Q: Calculate the vertical component of the internal force at B. Let W = 4 kips/ft.

A:

Q: F = 600 N 4 m 4 m- 30 n.

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: A Aluminum L = 3 ft A = 0.75 in.² E = 10 x 106 psi 2ft 3 ft. с B Bronze L = 4 ft A = 0.25 in.² E =…

A:

Q: Determine the internal normal force at point C of the beam. Give your answer in N and to 3…

A: Given:Required:Internal normal force at C

Q: Determine the vertical displacement of joint D. The truss is made from A992 steel rods naving a…

A: consider joint A angle at A = tanθ=21.5θ= 53.13° Fy=0FADsin53.13-20=0FAD=25KNFx=0FAB+FADCos…

Q: Determine the internal normal force, shear force, and bending moment in the beam at points B and C.…

A: Given :

Q: -4 m -4 m B 3m

A:

Q: Problem 2: The force F = {400i – 100j – 700k} lb acts at the end of the beam. Determine %3D the…

A:

Q: Determine the vertical displacement of joint C. The truss is made from A992 steel rods each having a…

A: Given :- The truss is made from A992 steel rods having diameter of 1 inch  To determine :- The…

Q: b.9N in

A: The Truss in the given problem is  asked to analyse using method of joints Method of joints is one…

Q: Determine the internal normal force at point C of the beam. Give your answer in N and to 3…

A: Given Loading UVL 200 to 400 N/mSpan 6 mTo find out Normal force at C

Q: Q2) Determine the vertical displacement of Point Ca) of trus shown below,if A Caren) of cross-…

A: Forces in Members Due to Given Load at A :  Support Reactions :∑H = 0 ⇒ HB = HD ............(1)∑V =…

Q: D. SM 3M 4M beam A I beam <105 200x MM A all = lo0 Mu? Eall= 200 GPm %3D → Find suppont ronctons ķ…

A:

Q: The free-body diagram of roller C is shown with the truss members assumed to be in tension. AC BC…

A:

Q: Compute for the forces on each member assuming that the triangles are equilateral

A:

Q: Determine the internal normal force, shear force, and bending moment in the beam at points B and C.…

A:

Q: 9. Using the Method of Sections, determine the force in member BC, to the nearest 1 Ibs. (Hint: Find…

A:

Q: Determine the magnitude of the horizontal force P (Ib) so that xg = 6 %3D ft.

A:

Q: Determine the magnitude of the pin force at C given  θ = 18° and P = 57 lbs.

A:

Q: F= 20 N , p-15N; H= 6N; K= 3N FIND IN COMPONENTS OF EACH FORCE Fx t Fy s THEN ZFx? ZFy? FIND THE…

A:

Q: The steel beam is fixed at A and supported by a roller at B. El is constant throughout the beam. A.…

A:

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.