Determine the loads developed in each column support at 2-A, 2-B, and 2-C, including the column weight. 16' Live load on the deck 40 psf %3D Deck weight = 9 psf Beam weight = 14 lb/ft %3D Column weight = 80 lb Please round to the nearest one. Foundation reaction at 2-A column = lb Foundation reaction at 2-B column: Ib %3D Foundation reaction at 2-C column = Ib MacBook Air

Q: 10 kN 6 kN/m 5 kN/m В 10 kN E 3 m 1.5 m--1.5 m--1.5 m-| CS CamScanner ile tarandı

A:

Q: Use the method of sections to determine the forces in members AB, FG, AH, and GH. State whether the…

A: Solution Draw the diagram

Q: Determine bar force member EF 10 KN 15 KN 10 KN D. E 0.9 m 0.9 m A G B IF 1.2m 1.2m 1.2m 1.2m

A:

Q: A W 530x92 supports a uniformly distributed load of 12 KN/m and equal concentrated load P at the…

A: Note:- The value of the length of the beam is not given so, taking L = Length of the beam  Given:- A…

Q: An exterior T-beam has a clear simply supported length of 6.75m. It has a clear distance to the next…

A:

Q: Floor System All question pertain to the following floor plan. The floor load is 60 Ib/ft?. Ignore…

A:

Q: b) The floor system shown is subjected to a total uniform distributed load of 20 kN/m². Sketch the…

A: w = 20KN/m2 The loading that acts along CDE is shown by the shaded region in the drawing. Total load…

Q: For the below truss system and loading: Complete an approximate analysis assuming the diagonals are…

A:

Q: The flooring system below is to be framed in steel, and has a dead load of 50 psf and a live load of…

A: Data Given: DL = 50 pcf LL = 40 pcf Asked: Mark the tributary area of the deck which is supported…

Q: Design a T-beam for SHEAR, for a floor 75 mm thick. f=21 MPa, fy = 420 Mpa, fy = 300 MPa 'yt Wo=…

A: Answer Check for shear stirrups requirement Shear stirrups needed when Vu > ϕ.Vc2 Vu = critical…

Q: The uniformly distributed live load on the floor plan in the figure given below is 65 lb/ft.…

A: A floor plan is given we need to find out the loading for girder G4Uniformly distributed load, Lo =…

Q: 270 N/m A -3m 6 m B

A: Given, Cantilever beam with uniform varying load    To find : Internal loading at C

Q: a om long simply supported beam has a width of 350mm and overall depth of 470mm the beam is…

A: Given,  Length of the beam = 6m Width (b) = 350mm Overall depth (D) = 470mm Effective depth (d) =…

Q: B 30⁰ P N 10 kN M L 20 kN FV 0 6 panels at 5 m K G 20 kN J 20 kN 30° 10 KN

A:

Q: If P = 114 kN, determine the normal stress produced at point H of the pier support shown. P 3 m…

A: Given that :-A pier support having, P = 114 kN is shown in the figure given in the question.Required…

Q: Analyze the structure below using cantilever beam method 25KN 3m 50KNB H 4m -6m -8m- SOLVE for the…

A: Given data in question  framed structure  Horizontal loads Span member length  To find out  Axila…

Q: Determine the reaction forces for beams B-1, B-2, and B-3. Column A Column B Girder G-1 open Girder…

A: T.L = D.L + L.L

Q: Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined…

A: Weight of the purlin = 79 N/m Dead load, DL = 720 N/m2 Live load, LL = 1000 N/m2 Wind load, WL =…

Q: Determine end reactions for Beam B-1 and Girder G-1. L1 B-1 • L1= 24 ft • L2 = 6 ft 'I G-1 Live load…

A: Given:- The value of L1 = 24 ft The value of L2 = 6 ft The magnitude of the live load = 30 psf The…

Q: Find the reactions at support A & B, provide the full solution along with its FBD.

A:

Q: The prestress T-beam section has a simple span of 6 m. The tendons is subjected to an initial stress…

A:

Q: "D.35. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 25.8…

A: Given Data: Ct=30mm Cb=35 mm bw=440 mm bf=710 mm hw= 470 mm t=90 mm Top layer of tension=4-28mm…

Q: "D.39. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 25.3…

A: Step 1: @Bottom, Ast=2463 mm2 @Top, Ast= 804 mm2 Xu/d =0.87x427.6x2463 / 0.36 x 25.3 x 790x530 =0.24…

Q: Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I…

A: We will solve this question in step no. 2

Q: P = 56.25 kN support conditions: pinned-pinned (k = 1.0) P = total load from governing load…

A: Given, Length of the column member=L=3 m K=1 width of beam=b=150 mm depth of beam=d=150 mm E=3640…

Q: Determine the allowable ultimate axial load on a rectangular short tied column 12 by 18 in. (300 by…

A: Given: Column dimension = 300 x 450 mm Number of reinforcement bars = 6 Diameter of reinforcement…