A rectangular gate, 1m wide supports water as shown in the figure below. The gate is hinged at the bottom and is kept in a vertical position by a concrete clock ( ϒ=23.6KN/m3 ) connected by a cable.a) Determine the hydrostatic force acting on the gate.b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position.c) Determine the minimum volume of concrete block required. A rectangular gate, 1m wide supports water as shown in the figure below. The gate is hinged at the bottom and is kept in a vertical position by a concrete clock ( Y=23.6KN/m3)connected by a cable.a) Determine the hydrostatic force acting on the gate.b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position.c) Determine the minimum volume of concrete block required.0.5mstop2mWaterhinge

Water at rest, is known to exert equal pressure in all directions, thus, the hydrostatic force…

Determine the hydrostatic force acting on the gate. b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position. c) Determine the minimum volume of concrete block required.

Determine the hydrostatic force acting on the gate. b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position. c) Determine the minimum volume of concrete block required.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.15P

See similar textbooks

Related questions

Q: Compute the hydrostatic force in kN acting on the gate.

Q: Problem 1 The gate shown is rectangular and has dimensions height h = 6 m by width b = 4 m. The…

A: Below is the clarified and detailed explanation for above tricky question.....if you are ok with my…

Q: 4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel…

Q: Determine the magnitude and direction of the HORIZONTAL component of the hydrostatic force (in kN)…

A: Given a tainter gate used to control water flow. It is required to Determine the magnitude and…

Q: -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of…

Q: What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is…

A: Given data Oil specific gravity Water Density of block Horizontal force Normal force

Q: 4. A vertical semi-circular gate with a diameter of 6 m is vertically submerged in water with its…

Q: The topic is all about Total Hydrostatic Force on Plane Surface. Show complete solution and…

A: Hydro-static Force: Hydro-static force is the total resultant force acting on a submerged body or…

Q: You are assigned to a project for the construction of a new tunnel. The tunnel will be 31 feet in…

A: Assuming the tunnel is of 1 ft length and the supports are continuous throughout the tunnel loading…

Q: 3. Two steel cables support a homogeneous bar AB weighing 2000 lb. The allowable stress for both…

Q: A homogeneous rectangular gate AB 7.9 ft wide and 10 ft long. Friction in the hinge is negligible.…

A: ρ=1000 kg/m3g=9.81 m/s2L=8.12 ft=2.475 mW=7.9 ft=2.408 mh¯=L2sin600=1.0717 m

Q: 3. For the gate shown, α = 45°, y₁ = 1 m, and y₂ = 4 m. Will the gate fall or stay in position under…

A: Given :

Q: The 2 m wide container is filled with water to the depth shown. Determine the resultant force on the…

A: aOn AFRA=ρwgh¯AAAAA=0.90.6=0.54m2h¯A=0.92=0.45mFRA=10009.810.45m0.54m2FRA=2383.83NDistance of…

Q: A tainter gate has a radius R, width W and height B. (B = 2R sin 0, where 20 from the hinge subtends…

Q: Q2. The 2.2-m-diameter pipe drains water from a reservoir, where the crown of the pipe is 3 m below…

A: Given: Diameter, d=2.2 m Area, A=πd24=π2.224=3.801 m2

Q: Problem 3- The support bracket for a water pipe that brings water from the city water system into…

Q: Sample Problems Talking: JOHN MAN SANTOS The gate shown submerged on water is hinged at B and rests…

Q: A vertical circular gate is 0.90 m in diameter is immersed in molasses (specific gravity = 1.4). The…

Q: A vertical rectangular gate 4 ft wide and 6 ft high, hinged at the top, has water on one side. The…

A: Consider the free body diagram;

Q: The hemispherical dome in weighs 36.9 kN and is filled with water and attached to the floor by 6…

A: Calculate force in each bolt,F=?

Q: For the portal frame shown in the given figure, the shear equation is B 4 m (a) (b) (c) (d) P MBC +…

Q: hydrostatic

Q: 1. A semi-circular gate of diameter "d" and radius "r" is submerged in a liquid and has its diameter…

A: Value of eccentricity is given bye=hcp-h¯h¯=2m+4r3πso,h¯=2m+423π=2.848

Q: The gate shown in the figure is hinged at A and rests on a smooth floor at B. The gate is 3m square…

A: The given data is: Air Pressure, P=7 kPa Specific gravity of oil S.G.oil=0.82 Weight of gate, W=5 kN…

Q: The hemispherical dome in weighs 37.9 kN and is filled with water and attached to the floor by 7…

Q: What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly…

Q: A rectangular gate, 1m wide supports water as shown in the figure below. The gate is hinged at the…

Q: diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is…

Q: Cable 60° Water Gate, 2.4m 3m Hinge. FIGURE Q2(c)

Q: Find the collapse load for the truss shown in the figure. All three bars have the same plastic axial…

Q: A rectangular vertical gate that has a width of 0.6 meters, height of 2.45 meters, and it weighs…

Q: 2 ft В seawater (SG = 1.03) 10 ft P 45° A

A: Weight of gate, W =600lbWidth of gate, B =20ftConsider unit depth of gate .Angle of gate with…

Q: Q| As shown in figure below, determine the weight of concrete cylinder, for equilibrium the gate AB.…

A: tension in cable =weight of block draw free body diagram of AB

Q: The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel…

Question

100%

A rectangular gate, 1m wide supports water as shown in the figure below. The gate is hinged at the bottom and is kept in a vertical position by a concrete clock ( ϒ=23.6KN/m³ ) connected by a cable.

a) Determine the hydrostatic force acting on the gate.

b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position.

c) Determine the minimum volume of concrete block required.

A rectangular gate, 1m wide supports water as shown in the figure below. The gate is hinged at the bottom and is kept in a vertical position by a concrete clock ( Y=23.6KN/m3)
connected by a cable.
a) Determine the hydrostatic force acting on the gate.
b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position.
c) Determine the minimum volume of concrete block required.
0.5m
stop
2m
Water
hinge

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2: To determine the hydrostatic force acting on the gate

VIEW

Step 3: To determine the tension in the cable

VIEW

Step 4: To determine the volume of the concrete block:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A rectangular gate is hinged as shown. The gate is 5 m high and 6 m wide. The specific weight of the water is 10000.0 N/m3 wall Water 00 Calculate the force, Fw [kN] on the gate 20 m due to the water hinge A= 30 m2 gate 5 m Fw stopper B Fw = 300 KN Force on the gate, Fw =- [kN] CRR Calculate the force, S [kN] due to the stopper (shown) on the gate to keep the gate in the closed position. Force on stopper to keep the gate closed, S = [kN]
The hemispherical dome in weighs 36.9 kN and is filled with water and attached to the floor by 6 equally spaced bolts. What is the force in KN in each bolt required to hold down the dome? Radius of the dome is 3 m, height of the pipe is 4 m and diameter of the pipe is 5 cm. Unit weight of water is 9.80 KN/m³. r BOLTS
the pipe? [-2. A steel pipeline with a nominal diameter of 24 in has an ID of 22.624 in (575 mm) and a wall thickness of 0.688 in (17.5 mm) carries a flow of 28 ft3/s (794 L/s). The pipe makes a short-radius 90° turn. What is the force developed in a buttress at the bend? What stress would be developed in the pipe by this change in direction if no buttress were provided? -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly closing a valve in the line? (K for water is approximately 10 percent of the value of E for steel.) SoLve Prob (6-3) REFERENCES 1. John Parmokie
the pipe? [-2. A steel pipeline with a nominal diameter of 24 in has an ID of 22.624 in (575 mm) and a wall thickness of 0.688 in (17.5 mm) carries a flow of 28 ft3/s (794 L/s). The pipe makes a short-radius 90° turn. What is the force developed in a buttress at the bend? What stress would be developed in the pipe by this change in direction if no buttress were provided? -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly closing a valve in the line? (K for water is approximately 10 percent of the value of E for steel.) SoLve Prob (6-3) REFERENCES 1. John Parmaki
Please solve this problem.asap. Thank you!
4 in. 200 kip 3 ft - The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. If the column is subjected to an axial force of 200 kip, determine the average normal stress in the concrete and in each rod. Each rod has a diameter of 1 in - change the applied force of 200 kip to 185.7 kip - change original diameter of each steel rod of 1 in to 1.35 in
Provide complete solution. Asap!
b) The floor system shown is subjected to a total uniform distributed load of 20 kN/m². Sketch the loading that acts along the members and CDE. 2 m E 3 m F G H 4 m 3 m
The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL EQUATIONS. Express your answer in kips. B. Determine the minimum force P required to open the seawater gate. Express your answer in kips.
The two-bar structure shown is pinned at A, B, and C. A sign weighing 20 kN is suspended from bar BC at points D and E, which are located at 0.8 m and 0.4 m, respectively, from the ends of the bar BC. If member AB is a steel pipe with inside diameter 20 mm, determine the smallest permissible outer diameter of the member if the working stress in steel is not to exceed 140 MPa.
What size pipe will maintain a shear stress at the wall of 0.624 psf when water flows through 300 ft of pipe causing a lost head of 20 ft.
The channel section carries a uniformly distributed load totaling 6W and two concentrated loads of magnitude W. Determine the (a) location of the neutral axis from the bottom, (b) the moment of inertia about that axis, (c) the maximum allowable value for W if the working stress are 4.0 MPa in tension, 8.0 MPa in compression, and 2.4 MPa in shear. 20 mm ←140 mm → 20 mm 6W (total) W 4 m 20 mm A 1.0 m/ O B 41.01 W 140 mm ΝΑ