Determine the horizontal displacement (mm) of joint C. 300 lb. 300 lb. 13 ft 0080 B 5 ft 12 ft 13 ft 12 ft 008

Q: = constant 5. Bernou lli's equation is expressed as asY'2g Research on the corresponding units por…

A:

Q: For the truss shown in Figure 3, members AC and BC have cross sectional area of 2 in.² while members…

A:

Q: Determine the support reactions at A and B: 1- Assume A is a pin and B is a roller?? 2- Assume A is…

A: From the given question it is required to calculate the unknown support reactions by considering…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: 6-65. Determine the moment of inertia of the area about the x axis. h -b- Prob. 6-65

A:

Q: Given data on a conducted differential leveling survey, supply the missing figures and write your…

A:

Q: 3. Closed Traverse: COURSE DISTANCE BEARING АВ 495.85m N 05°30' E N 46° 02' E S 67° 38' E S 12° 25'…

A:

Q: Water discharging into a 10 m wide rectangular horizontal channel from a sluice gate is observed to…

A:

Q: H.W1 The beam is subjected to the linearly varying distributed load. Determine the maximum…

A: step 1-

Q: 1. A dam 15 m long retains 7 m of water, as shown in Figure. Find the total resultant force acting…

A: Total force can be calculated as the product of area of pressure diagram and length of dam. Center…

Q: Derive the formula for the maximum (+/-) shear and maximum (+/-) bending moment of the simple beam…

A: The algebraic sum of the vertical forces at any section of a beam to the right or left of the…

Q: Determine the MOMENTS acting at the ends of each member of the frame shown below. Assume the…

A:

Q: *6-60. Determine the moment of inertia for the area about the x axis. 6-61. Determine the moment of…

A: Consider the figure,

Q: Draw the shear diagram, moment diagram, and elastic curve of the loaded structure. 60 k 150 k-ft 10…

A: Draw the shear diagram, moment diagram, and elastic curve of the loaded structure.

Q: The coordinates of A, and the bearing and horizontal distance from A to B (line AB) are provided in…

A:

Q: 6-1. Locate the centroid of the arca. y = ax -b- Prob. 6-1

A:

Q: QUESTION Compute the reactions at support for an overhanging beam as shown in the figure. Then, draw…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: diagrams

A:

Q: AA County Foad c6o wie) For the rectangular shown, the county road is to be place such that the…

A: Given: The diagram is a rectangle.

Q: PROBLEM THEORY-10. A 4-m propped cantilever beam is loaded as shown in the figure. E = 200 GPa and I…

A:

Q: 6-3. Locate the centroid of the area. *6-4. Locate the centroid y of the area. 4 m 4 m

A: To find centroid of given curve

Q: Equation method please

A: REACTION FORCE AT FIXED END: ∑FY=0RA-17-12×9×6=0RA=44 kips∑MA=0-MA+12×6×9×23×9+17×14=0MA=400 kips-ft

Q: A planned municipality anticipates a waste collection rate of 60 tons per day, 5 days per week.…

A: Given Data: waste collection rate = 60 tons/day there are 5 days per week. Collection Vehicle…

Q: El is constant for the beam shown in Figure 4. • Compute the rotation of the beam at B. • Compute…

A:

Q: i need all parts of question on the right hand corner solve I STATED FILL IN THE BLANKS.

A: Only 3 subparts can be answered at a time according to guildlines. Please resubmit the question…

Q: method of double integration, find the value of the deflection a 120lb 100lb.ft 75lb.ft 2.0m 8.0m ><

A:

Q: -71. Determine the moment of inertia for the area about the y axis. 4 in. 16 in. - Prob. 6–71

A:

Q: Question 1) Determine the x and z components of reaction at the journal bearing A and the tension in…

A: F1 = -800 k F2 = 350 j

Q: cos a - sin Lsin a n a 1+ A = (1 – A)

A:

Q: (a) Determine h value in cm.

A:

Q: A horizontal curve has its middle ordinate, M, 150.00 m and its external distance, E, 300.00 m. That…

A: The given data is as follows: Middle ordinate, M=150.00 mExternal distance, E=300.00 mNumber of…

Q: Problem III. Determine the support reactions at B and the location of the maximum deflection for the…

A:

Q: 5.116 A pump is to move water from a late to a large, pressurized tank at a rate of 1,000 gallons in…

A:

Q: Determine the slope and displacement at point A using DIM. Assume C is pinned. 6KN/m 3m 3m

A:

Q: 3. A 12 ft cantilever beam is subjected to a uniformly distributed load at the entire span and a…

A: Consider a section x-x at distance x from point B.

Q: Double integration method, please include complete solutions and figures

A: Force in vertical directionRA + RC = 12×25×4 + 25×3 = 125 KN ........1Sum of the moment at point…

Q: Compute the values of slope and deflection at points B and C. Assume El is constant.

A: take C as origin point and find Moment equation of the beamMx=120x-40   singularity function valide…

Q: 5. The frame shown is supported by a hinge at A and a roller at E. Compute the horizontal and…

A:

Q: Problem 4 Find the point where the maximum deflection of the real beam occurs by the conjugate beam…

A:

Q: 3. Triaxial tests were performed on clay samples on clay samples taken from the stratum shown below.…

A: Given: Triaxial tests were conducted on clay samples taken from stratum as shown in the figure below…

Q: Determine the Vertical Deflection at F. Indicate the negative sign if the answer is downward For the…

A:

Q: Problem III. Determine the support reactions at B and the location of the maximum deflection for the…

A:

Q: Problem 1 From the open compass traverse shown, if the forward bearing of line AB is N 45°20' E,…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.