Determine the Height of a chimney with a static draft of 12 mm if the losses total draft is 4 mm, the ambient air temperature is 35 ° C and the exhaust gas temperature is 450 ° C. The fuel consumption of the boiler is 600 kg / h, the mass of the exhaust gas is 16 kg, also determine the air mass ma, the diameter of the chimney and the velocity of the exhaust gases.

Determine the Height of a chimney with a static draft of 12 mm if the losses total draft is 4 mm, the ambient air temperature is 35 ° C and the exhaust gas temperature is 450 ° C. The fuel consumption of the boiler is 600 kg / h, the mass of the exhaust gas is 16 kg, also determine the air mass ma, the diameter of the chimney and the velocity of the exhaust gases.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
You are designing a pin-style heatsink for forced cooling of an IC. A small fan blows RT air into the heatsink at about 2.3 ? ? . The aluminum pins are 2mm in diameter and have a constant surface temperature of 120°?. The heatsink is 100mm x 100mm and the pins have an inline arrangement with a transverse pitch of 4mm and a longitudinal pitch of 6mm. What is the total heat dissipation of this heatsink? The pins are 30mm high. Note RT=25 celsius
A 30mm ID, 50mm OD aluminum round tube passes air through it at a rate of 0.08 m^3/s. A 100W electric heater blanket covers the outside of the 2m long tube. If the air enters the tube at 100 celsius , what temperature does it exit at? Assume that the heater blanket is perfectly insulated on the back side (no heat loss out the back). Note-RT is 25 celsius
Water flow in steel pipe at a temperature of 50o C as shown in the figure. The pipe is wrapped with thermal isolation. Air is flowing over the pipe at a temperature of -5o C and a speed of 3 m/sec. It is known that 1kWh costs 0.05$ Find the daily cost of the heat losses per meter without the pipe isolation? What is the daily cost saving when using the isolation?
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Air flows from a 10cm pipe in which the temperature and pressure are 4-C and 280kpa, respectively, into a 5cm pipe in which the pressure is 147kpa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 280N-m/kg-K.
A getter screen consists of a cylinder of length l = 0.3m, diameter d=0.25m and its circular based plate. The getter screen is cooled with liquid nitrogen and coated completely with deposited titanium providing a constantly fresh surface. Sticking probability s=1 for N2 and mean thermal velocity = 470m/s. Find the pumping speed.
In cold climates, weather reports usually give both the actual air temperature and the "wind-chill" temperature, which can be interpreted as follows. At the prevailing wind speed there is a rate of heat loss per unit area q, from a clothed person for an air temperature Te. The wind-chill temperature Twe is the air temperature that will give the same rate of heat loss on a calm day. Estimate the wind-chill temperature on a day when the air temperature is -10°C and the wind speed is 10m/s, giving a convective heat transfer coefficient of 50 W/m² K. A radiation heat transfer coefficient of 5 W/m² K can be used, and under calm conditions the convective heat transfer coefficient can be taken to be 5.0 W/m² K. Assume a 3 mm layer of skin (k = 0.35 W/m K), clothing equivalent to 8 mm-thick wool (k = 0.05 W/m K), and a temperature of 35°C below the skin. Also calculate the skin outer temperature.
Estimate the mass-transfer coefficient for moist air flowing normal to a 25 mm diameter tube (Nu = 0.615 Re0.47). The air velocity is 0.5 m/s. Assume standard air.
Q2:A) Define the bulk temperature (Tn), and prove that : T₁, - 2 ur dr B) Ethylene glycol flows at 0.01 kg/s through a 3 mm diameter, thin walled_tube. The tube is coiled and submerged in a well-stirred water bath maintained at 25 °C. If the fluid enters the tube at 85 °C, what heat rate and tube length are required for the fluid to leave at 35 °C ? At 60 °C, μ = 0.00522 kg/m.s, k = 0.26 W/m.K, C, 2562 J/kg.K. -
Blue and yellow streams of paint (each with a density of 1.6 slugs/ft³ and a viscosity 1500 times greater than water) enter a pipe with an average velocity of 9 ft/s as shown in the figure below. Would you expect the paint to exit the pipe as green paint or separate streams of blue and yellow paint? Explain. Repeat the problem if the paint were "thinned" so that it is only 10 times more viscous than water. Assume the density remains the same, and the temperature is 60°F. Classify the flow. Splitter Laminar Yellow Blue Laminar flow has mixing only by molecular diffusion. Turbulent flow has mixing due to large scale fluctuations. Reynolds number is a measure of whether flow is laminar or turbulent. Classification of viscous flow as laminar or turbulent dictates how the flow is analyzed. What is the Reynolds number for the flow with a viscosity 1500 times that of water? Re= 2 in. What is the entrance length for this Reynolds number? le= ft Green? 25 ft