Determine the height h of the column of mercury in the tube if the level of water in the tube is 0.2 mand the dimensions of the oil and the water listed in the diagram. Let poil = 900 kg/m³, pwater = 1000kg/m³, PMercury = 13,500 kg/m³.A0.4 mOilB0.3 mhWaterMercury0.2 m

Step 1:Given: ρoil=900kg/m3ρwater=1000kg/m3ρmercury=13500kg/m3 Step 2:Hydrostatic pressure: It is…

Answered: Determine the height h of the column of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The maximum blood pressure in the upper arm of a healthy person is about 120 mm Hg. If a vertical tube open to the atmosphere is connected to the vein in the arm of the person, determine how high the blood will rise in the tube. Take the density of the blood to be 1050 kg/m³. Food for thought: How do you experimentally measure blood density?
A gate (shown in blue with a fixed angle of 135°) in a water tank has a frictionless hinge (a linear hinge going into the paper shown in red). The gate and hinge are both 2 m long (into the paper). Determine the height of water (h) needed to first open the gate. 1.00 m 135° 0.20 m WATER h
1. A device for measuring the specific weight of a liquid consists of a U-tube manometer as shown. The manometer tube has an internal diameter of 0.5 cm and originally has water in it. Exactly 2 cm³ of unknown liquid is then poured into one leg of the manometer, and a displacement of 5 cm is measured between the surfaces as shown. What is the specific weight of the unknown liquid? Answer: Y = 0.5 cm. T 5 cm ↓ Water
A barge floating in fresh water (ρ = 1000 kg/m3) is shaped like a hollow rectangular prism with base area A = 650 m2 and height H = 2.0 m. When empty the bottom of the barge is located H0 = 0.55 m below the surface of the water. When fully loaded with coal the bottom of the barge is located H1 = 1.8 m below the surface. Find the mass of the coal in terms of the given data.
Determine the height of the mercury in the tube if the level of water in the tube is h = 0.3m and the depths of the oil and water in the tank are 0.6 and 0.5 m, respectively as shown in Figure Q5. Take po = 900 kg/m³, pw = 1000 kg/m³, and PHg= 13550 kg/m³. 0.6 m 0.5 m B h'=0.3 m
The total pressure force of a square plate is 25 kN, placed vertically in water so that the center of the plate is 1.5 m below the free surface. Determine the size of the plate and the depth of center of pressure. The above square plate is taken out of the water which weighs 370.5 N in air and 180.3 N in water of specific gravity 0.99. Find the volume and specific gravity of the square plate. Draw a neat sketch.
Chemistry The contact angle for water in a clean glass is zero. Calculate the surface tension of waterin a 0.3 mm diameter vertical tube if the water rises to a height 4.96 cm above the liquidoutside the tube, knowing that specific gravity of water equals 998.2 kg/m 3 and theacceleration due to gravity equals 9.806 m/sec2
B-A manometer connected to a tank reads 230 mm of oil (if the oil density is 1500 kg/m3) at a location where Atmospheric pressure is 1.03 mbar .Determine the absolute pressure in bar.
The device shown is the buoyancy measurement device used to measure the liquid height change. A pressure sensor is installed at the bottom of the tank, and a force sensor is installed to measure the upward force on the horizontal lever. The distances to the pivot point from the force sensor and cylinder are X1 and X2, respectively. The reference pressure at the reference liquid height, h0, to the bottom of the cylinder is pref. (4) If the force measured by the force sensor is Fsensor = 7.53 N, X1 = 1.58 m, X2 = 0.17 m, the diameter of the cylinder is D = 0.05 m, and the specific weight of the liquid is γf = 8.70 kN/m3, calculate the liquid height difference, Δh, relative to the reference height h0. __________ m.
2) Consider the system shown in the figure. If a change of 0.9 kPa in the pressure of air causes the brine- mercury interface in the right column to drop by 5 mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A2/A1. Air Brine pipe SG = L1 Water Area, A Arca, A, Mercury SG = 13.56

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the height h of the column of mercury in the tube if the level of water in the tube is 0.2 m and the dimensions of the oil and the water listed in the diagram. Let poil = 900 kg/m³, pwater = 1000 kg/m³, PMercury = 13,500 kg/m³. A 0.4 m Oil B 0.3 m h Water Mercury 0.2 m