Determine the gradability of a crawler tractor pulling a high - pressure rubber tyred self loading scraper and its load. The following information is available :- (i) Tractor horsepower, =180 (ii) Weight of tractor = 18, 400 kg (iii) (iv) Drawbar pull in 1st gear = 15300 kg Available drawbar pull = 13005 kg. (v) Weight of loaded scraper = 35850 kg. Haul road rutted and uneven earth (vi) (vii) Rolling resistance for tractor = 23 kg/tonne (viii) Excess rolling resistance for scraper = 95 kg/tonne (ix) Rolling resistance for scraper = 95 kg/tonne (x) Pull required/tonne/1% grade = 9 kg.

Determine the gradability of a crawler tractor pulling a high - pressure rubber tyred self loading scraper and its load. The following information is available :- (i) Tractor horsepower, =180 (ii) Weight of tractor = 18, 400 kg (iii) (iv) Drawbar pull in 1st gear = 15300 kg Available drawbar pull = 13005 kg. (v) Weight of loaded scraper = 35850 kg. Haul road rutted and uneven earth (vi) (vii) Rolling resistance for tractor = 23 kg/tonne (viii) Excess rolling resistance for scraper = 95 kg/tonne (ix) Rolling resistance for scraper = 95 kg/tonne (x) Pull required/tonne/1% grade = 9 kg.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 10 KN 30 30 D 6 m B 30 30° -3 m- 3 m

Q: Q.2 Two shafts of different materials having same length are joined in series and subjected to a…

A: Option (d)1:24 is the correct option

Q: Find the maximum load P that can be supported by the tripod if the force in any leg is limited to…

Q: A 30m tape is supported only at its ends and under a steady pull of 8kg. If the tape weighs 0.91 kg,…

A: Introduction- The Tape correction(s) in surveying refers to the process of adjusting measurements…

Q: basic equations and forces analysis are needed for reservoir and pipe folw.

A: The artificial or natural storage of water with help of dam is known as a reservoir.

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

Q: 5.b the diagram below represents the chassis rail of the lorry above. Draw the shear force and…

A: Data given Find the shear force and bending moment diagram

Q: A steel pipe column (standard pipe weight) to support a load of 40 k and a length of 20 feet. Fy 36…

A: Given data: Fy= 36 ksiLoad on column = P = 40 K⇒Fy=PAor, A=PFy=40 k36 ksi=1.11 in2…

Q: Pj = 4.0 kN P2 = 8.0 kN 1.0 m B 4.0 m- - 1.0 m-

Q: A column in a building is subjected to the following load effects: 9 kips compression from dead load…

A: D= 9 kips, S=6 kips, L= 0, Lr=5 kips, R=7 kips, W=6kipsD= Dead load S= Snow load L= live load due to…

Q: THE FOLLOWING INFORMATION IS TO BE USED IN THE NEXT 2 (TWO) QUESTIONS. Twelve (12) lines are strung…

A: Given:- A frictionless block-and-tackle system of a drilling rig is given The total number of…

Q: A wooden column with modulus of elasticity of 136280 N/mm´ is hinged at one end and fixed at the…

A: Modulus of elasticity = E = 136280 N/mm2 Total length of the column = L = 375 cm Width of column =…

Q: 12 ft 'F 3 ft D 30 6 ft B -8.4 ft- 2.2 f 1.4 ft

Q: Wile E. Coyote prepares a trap to kill (I hope so, too) Road Runner for good. What is the minimum…

A: Given:- The mass of the steel cylinder = 1 ton The angle of friction between the pulley and the rope…

Q: Question 9 The distributed load shown is supported by a box beam shown using five pieces of 50mm x…

Q: 1. A column in a building is subjected to the following service load effects: Dead Load = 40…

Q: As part of a design team for a new construction crane, you are responsible for selecting aflexible…

Q: A catwalk of an onion cold storage building is designed for a uniform dead load of 1.6 kPa and a…

Q: An existing building in Amman has been renovated. As a structural engineer, you are requested to…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Manny Pacquiao owns a hydraulic press for his training to box in the presidential race. It is filled…

A: Given, Relative density = 0.82

Q: QUESTION 1) For the given load-bearing system, construct the internal loading diagrams (N, T, M) 20…

Q: A square steel rod 20 mm x 20 mm in section is to carry an axial load (com- pressive) of 100 kN.…

A: Given,

Q: What is the equivalent concentrated load and its location for each of the following: a. Triangular…

Q: Design a tie column to carry an axial dead load of 600 kN and an axial live load of (1.6X1+2.6X2)…

A: Given Fy=X2=403MPaFc=X1=67.9MPaDead load=600kNlive=1.6X1+2.6X2Total=600+1.6×67.9+2.6×403…

Q: Determine the force in member CD (N without decimal places), positive if it is tension and negative…

Q: A ductile material is subjected to a tensile test. The yield strength was determined to be 100 MPa.…

Q: 2. s) According to Boussinesq and Westergaard conditions, determine the resulting load at a point 15…

A: 2We have formula for BoussinesqΔσ=Qz232π11+rz252We have formula for…

Q: Draw the free-body diagram for the following problem.The jib crane shown.

A: Free body diagram is a graph or image of an object in which all the forces, moments and reaction…

Q: Structural engineering

A: Step 1:Step 2:Step 3:Step 4:

Q: Consider a column which is subjected to a compressive load. A probable failure will be by buckling.…

A: A column which is subjected to a compressive load. A probable failure will be by buckling.We have to…

Q: Determine the total Dead load, in SI units, for the following materials of a floor system: Carpet…

Q: A barge shown, diagrammatically supports the load W1 and W2 for every one meter strip along the…

Q: culate the ultimate concentrated load in KN based from the following service loàds: Dead…

Q: A column in a building is subjected to a compressive load from the following sources: 10 kips from…

Q: A belt conveyor is required to deliver crushed limestone having a bulk of 75 lb/ft³ at the rate of…

A: Step 1

Q: Determine if the beam is adequate to carry the loads with respect to shear. Check in LRFD only.…

Q: 1. A Hydraulic press has a ram of 30 cm diameter and a plunger of of 2 cm diameter. It is used for…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

Determine the gradability of a crawler tractor pulling a high
- pressure rubber tyred self loading scraper and its load. The
following information is available :-
(i) Tractor horsepower, =180
(ii)
Weight of tractor = 18, 400 kg
(iii)
(iv)
Drawbar pull in 1st gear = 15300 kg
Available drawbar pull = 13005 kg.
(v) Weight of loaded scraper = 35850 kg.
(vi) Haul road rutted and uneven earth
(vii) Rolling resistance for tractor = 23 kg/tonne
(viii) Excess rolling resistance for scraper = 95 kg/tonne
(ix) Rolling resistance for scraper = 95 kg/tonne
Pull required/tonne/1% grade = 9 kg.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Rolling Resistance

VIEW

Step 3: Maximum Possible Grade Calculation

VIEW

Step 4: Maximum Possible Grade Calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Current Attempt in Progress Plot the magnitude of the resultant R of the three forces as a function of 0 for 0 ≤ 0≤360°. After you have the plot, determine the value of 0 which makes the magnitude R of the resultant of the three loads (a) a maximum and (b) a minimum. Record the magnitude of the resultant in each case. Use values of = 64° y = 22°, F₁-59 N, F₂ = 129 N, F3 = 71 N. Answers: (a) maximum R= i N when 0= i (b) minimum R = i N when 0- i
۱%۹۳ ||. 1:00 Answered: Q2: Detrmine the .. bartleby.com = bartleby Q&A I 8 Engineering / Mechanical Engineeri... / Q&A Library / Q2: D... Q2: Detrmine the maximum Torque (T) th... Question Q2: Detrmine the maximum Torque (T) that can be applied without exceed the shearing stressess and the angle of twist at the free end provided in the Table below: Rod D (m) Tall (MPa) G (GPa) 0 (degree) Steel 40 100 83 Bronze 50 90 35 4 Aluminium 60 80 28 8T 2T 3T Aluminium Bronze Steel 2m 1.5m 1m Expert Answer Step 1 Given dlala الإنجليزية II >
Civil Engineering Quick question?How is live load determine for a bridge?-What factors are considered and how do you know this (Do you need to know "x" to get "y")?For example lets say If you're given a dead load of 50,000 lbs or or 50 kips for a bridge can you use this information to determine a liveload? if not what other factors is needed?-lets also say the bridge span length is 205 ft.
01. For the table below. Find the equivalent ale load For standard ale load is 90 kN. Axle load N Tensile strain at the bottom of the binder course (mm) 3 9 70 90 130 150 And if E the modulus of elasticity = 2500 kN/mm fi= 18000 f₂=0.3 f3=0.1
Four wheel loads rolls as a unit across a 19-m span. The loads are 40 kN, 40 kN, 30 kN, and 10 kN separated respectively by distances of 2 m, 3 m and 6 m. Compute the maximum shear in kN.
skip if you arleady did this or else downvote
need in 30 mins asap auto like
Please show complete answers and fbd
A skip for a mine shaft weighs 2000lb and is to lift a maximum load of 3000lb from a depth of 1000ft. The maximum speed of 20fps is attained in 5 sec. (a) What sizes of 6 x 19, IPS rope and sheave should be used for indefinite life and for N=1.3 on the basis of fatigue? (b) What is the design factor on the static basis? (c) What sizes of rope and sheave are required if the number of cycles (bending and unbending) in the desired life is 200,000? What is the corresponding static design factor? (d) What is the elongation of the rope found in (c) if the 3000lb load is added while the hoist hangs free at the bottom?(Use Faires)
Bridge truss problem. Answer is provided. I need an explanation and how it is solved given the solution. Also I would like to know if it is compression or tension.
help on both please
For the beam shown, calculate the beam slope at D. Assume that a = 3.8 ft, b = 5.7 ft, c = 7.6 ft, w = 1450 lb/ft, P = 3400 lb, and El = 600000 kip-in.². Answer: 8D = i a W Save for Later B b eTextbook and Media rad P C C 0 Attempts: unlimited Submit Answer