Determine the forces P1 and P2 needed to hold the cable in the position shown, i.e., so segment BC remains horizontal.

Q: Problem No. 1.: All bars in the truss shown are 25-mm diameter steel rods (E = 200 GPa). %3D SET P1,…

A:

Q: 1.a) Determine reactions at A and D by drawing a free - body diagram and set up three equations of…

A:

Q: Determine the force in members BG and GH of the truss shown in Fig. 2-a. State whether the members…

A:

Q: Determine the reactions at A and C; Determine forces at members FE, CE, and CD using Methods of…

A:

Q: 3. Determine the force in members DJ, CD, CJ and KJ of the truSs which serves to support the deck of…

A: Given data in question  Truss Span member length  Point loads To find out  Member forces Note I have…

Q: 12-1M. Determine the forces in the members of the truss in Figure 12-11M. 30 kN. A 30 kN do 60 kN do…

A:

Q: Determine the force in members CD and KL of the truss shown. 3 kips 3 kips 3 kips 3 kips 3 kips 3.0…

A:

Q: *3-32. Determine the forces in all the members of the complex truss. State if the members are in…

A:

Q: Determine the forces in the members indebtified by "x" of the truss shown by the method of sections.

A:

Q: Determine the vertical and horizontal positions of the shear centre of the stiffener section below…

A: shear centre is point if at which load is applied on twisting will occur in the section  e = (…

Q: - DETERMINE FORCES IN ALL MEMBERS IndiCATE WETHER FENSION I OR T COMPRESSION Гом A B 10m 30° гом So…

A:

Q: Fig. 3 Q 4/Determine the force in member JM of the loaded truss. D C E В F 5m 4 m M N. 4m A 3m 3m K…

A: They ask to find force in member JM

Q: Draw the ILD for the forces in members P, Q, R, S of the truss shown in Fig. 3 m 3 m 3 m 3m 水 水 0₁ 3…

A:

Q: Determine the support reactions and all internal pin forces.

A:

Q: 4 5 B 100 KN 125 kN 4 at 6 m = 24 m H D 50 kN 4.5 m T E LILIL

A:

Q: *3-32. Determine the forces in all the nber complex truss. State if the members are in tension or…

A:

Q: PROBLEM NO. 2 FOR THE TRUSS SHOWN, DETERMINE THE FOLLOWING: a) TO TAL REACION AT SUPPORT'F' IN b.)…

A:

Q: Analyze the given truss and find member forces.

A:

Q: Determine the force in members EC, DC, BZC of the truss shown

A:

Q: Determine the location e of the , for the thin-walled member having the The member segments have the…

A:

Q: Determine the location e of the shear center, point O, for the thin-walled member having the cross…

A: Given :

Q: Q1: Specify the type of the truss shown in Fig.(1). Then, find the forces in bars FJ and JH. كومبلكس…

A: A truss is given with hinged support at A and roller support at K.The truss is loaded with 60kN…

Q: *6-68. The bridge frame consists of three segments which can be considered pinned at A, D, and E,…

A:

Q: 6 Force in member AD of the truss shown is -- a) zero {MA = 0 b P/V2 c) P d) v2 P 10% 0 BY = A…

A:

Q: 3. Use the method of joints to solve for each of the bar forces of the truss shown. -6m 12 kN 24 kN…

A: The given truss is shown below:

Q: Get the degree of kinematic indeterminacy of the following structures

A:

Q: Set P₁ = 36 kN, P₂ = 26 kN. (Figure 1) Figure B G -1.5m 1.5m-1.5m- P₁ F < 1 of 1 -1.5 m P₂ 2m E

A:

Q: Determining the forces in three members on the right- hand side of the truss members HD, CD, and GD.…

A: To find out the forces in the member of HD, CD, gD, HI, BH and BC.

Q: Q3) Use the method of Joints to calculate the force in each member of the truss illustrated as well…

A: Use the method of Joints to calculate the force in each member of  truss illustrated as well as the…

Q: By method of sections, determine the bar force in members bd, ef, de, ce. of the truss shown in…

A: Given Data  Find the forces in member bd, ef, de and ce using method of section.

Q: The total degree of static indeterminacy of truss shown below is

A:

Q: Use the method of sections to determine the force in members CD, and GF of the truss and state if…

A: Given;

Q: 2 kN 1.5 m D 0,8 m B. E H G |F -1 m V1.5 kN 1 m- 2 m 2 m-

A:

Q: 30 kN 3 m 30 kN NG 3 m D C 4 m 4 m 4 m FIG. P4.11

A:

Q: 2.Determine the nominal moment strength Mn of the pretensioned bonded member where f'c = 5 ksi fpu =…

A:

Q: Determine (approximately) the forces in the members of the truss. The diagonals are to be designed…

A: Shear panels are ABEF and BCDE From A to B , Shear force=-10+20 Shear force=10kN Therefore member AE…

Q: shown have a ectional ns have a diameter of 20mm. etermine: cross- area of 500 mm and all ne axial…

A: