Determine the force (in kN) in members {BF, BG & AB}. Report the force in members under compression with a negative sign while entering the answer. Assume F₁ = 5 kN, F₂ = 5 kN, F3 = 10 kN, F4 = 10 kN, and a = 4 m. You are encouraged to use the method of sections for this question

Determine the force (in kN) in members {BF, BG & AB}. Report the force in members under compression with a negative sign while entering the answer. Assume F₁ = 5 kN, F₂ = 5 kN, F3 = 10 kN, F4 = 10 kN, and a = 4 m. You are encouraged to use the method of sections for this question

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=2.0 m, LBc=6.9 m, P=19 kN, bf=180 mm, t₁=14 mm, tw=9 mm, d=159 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. A Answers: OmaxT maxC = LAB i i P B LBC bf + Cross section MPa MPa P LCD D X
Determine the forces in members CD, GD, GH. use method of sections. *use 3 decimal place in rounding off all throughout the solution.
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. Answers: AB= AG= BC = i BG= 1 CF= i CD= 1 CG= i DE= DF= 1 1 i EF= i FG = 1 B G 6.6 KN F 2.8 kN 3 3 3 3 3 3 3 3 3 3 3 kN D E
Please answer B only.
Completely solve and box the final answers! WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS.
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 7 kN, and w = 2 kN/m. P KN cm w kN/m (not scaled) 290 mm a m bm b Ri R2
A cantilever beam with length of 3.2 m is reinforced with As=5720 mm^2 tension reinforcement and compression reinforcement A's =1905 mm^2 placed at 60 mm from extreme compression fiber. The effective depth is 550 mm and width of 400 mm. Use f'c=35 MPa and fy=415 MPa. 1. Calculate the magnitude of the neutral axis. 2. Determine the compressive force of the section. 3. Determine the safe concentrated live load that can be placed at the free end if the beam carries a total ultimate uniform load of 35 kN/m.
Solve the problem with complete and neat solution. Draw the figure. Determine the forces in members IH, KC, and BC of the truss using method of sections. State whether each member is in tension or compression. 60KN A 3m B 3m K H 4m C 3m 60KN D 3m F E
Please write the solution on paper. Additionally, please use "method of joints" when solving for subpart c.
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.65x105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?
STRENGTH OF MATERIALS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTION AND FBD. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. Solve for the stress of all members (AB,AC,BC,BE,BD, CE,DE,DF,EF,EG,FG,FH,GH) for the truss given below. The cross-sectional areas of the members is as follows Top and Bottom Chords = 350mm, Post = 300mm, Web/diagonals = 250mm.
Please help me with the following question. You can use the second photo as reference and please put the whole process and solution because I’m having a difficulty with understanding it. Thank you very much. Use Method of Sections SN=66