Determine the effective grade (%) for the total resistance of goong uphill? Facts:• A fully loaded wheeled scraper (empty weight = 30.0 tons; fully loaded weight = 80.0 tons) musttravel up a 3.0 % slope on a muddy haul road.The average tire penetration of the machine is estimated to be 4.0 inches.After dumping the loaded weight, the scraper returns downhill with an empty weight.

Given data,Scraper empty weight=30.0 tonsScraper fully loaded weight=80 tonsslope=3% on muddy haul…

Answered: Determine the effective grade (%) for…

Engineering

Civil Engineering

Determine the effective grade (%) for the total resistance of goong uphill?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A grader will be used to maintain 4 miles of haul road. It is estimated the work will require removing ruts with three passes in first gear, leveling the road with two passes in second gear, and final shaping of the road with four passes in fourth gear. Us an efficiency factor of 55%. Grader speeds are provide in the chart. Estimate the time requirement for this task. Forward Gears Maximum travel speed (mph) First 2.5 Second 3.1 Third 4.2 Fourth 7.0 17.4 hours 18.4 hours 15.8 hours 16.5 hours
Question #4: A wheel-tractor scraper is operating on a level grade. Assume no power derating is required for equipment condition, altitude, temperature, and so on. Disregarding traction limitations, what is the maximum value of rolling resistance (in pounds per ton) over which a loaded scraper can maintain a speed of 20 mph? Use the scraper specifications in Table 8.1 and the performance charts in Figures 8.8 and 8.9.
Following figure shows the mass-haul diagram for a road project. -Mass-Haul Diagram Volume (m³) 20000 15000 10000 5000 0 -5000 -10000 -15000 -20000 0 500 1000 1500 2000 Distance from the start of the project (m) 2500 O The soil will have to be moved from right towards the left ● Cannot be determined from the given information O The soil will have to be moved from left towards the right. O There will not be any movement of soil. 3000 3500 The section from 1400 m to 1600 m has been identified as a free-haul section. What will be the direction of net soil movement within this free-haul section?
Q1) A. Briefly describe the following: - 1. Under what conditions would you prefer borrowing new material from a borrow pit for highway embankment over using material excavated from an adjacent section of the road?
Q1. Geologists investigating a landslide surveyed the elevation of a hillside and found it to be 872 m at the bottom and 991 m at the top. The survey points were horizontally separated by 465 m. How steep is this hillside as a percent grade if 45 degrees is a 100 percent grade? percent grade = ........... % Q2. Enter your answer in scientific notation. The discharge (Q) of a stream is the velocity (v) times the cross-sectional area (A): Q = vA. What is the discharge of a stream with a velocity of 2.1 m/s and a cross-sectional area of 54.2 m2? Q = ........ × 102 m^3/s
Estimate the time required (in hours) for a dragline to excavate material to be placed and compacted on a parking lot construction site, where 7200 CCM of material is needed. Use the following information: Dragline size = 1.53 m³ Swing angle = 90° 4 Average depth of cut - 3.36 m Material sand and gravel Job efficiency = 45 min/h Soil shrinkage 12% Your Answer: Answer
You are a platoon leader in the 10th Engineer Battalion in Schweinfurt, Germany. You are planning to take your tracks across an embankment in Hohenfels that is supported by a concrete retaining wall as shown in the figure below. You estimate that the surface load due to the weight of your vehicles will be 150 psf. You have previously worked with the insitu soil while installing a culvert and estimate the soil parameters to be as depicted on the figure. Determine whether or not you should drive your tracks over the embankment. Make sure you check the factors of safety against sliding, overturning and bearing failure. 1.5' Truck Load q = 150 psf Well Graded Sand (SW) 13' SW 4" 3.5X X 7' 12' Properties O'= 36°, c 0, Yt = 125 pcf, Yconcrete = 150 pcf Ösoil-concrete = 24° Well Graded Sand (SW)
A 7000 meters long and 8 meters wide road is to be constructed in a remote region. Cut and fill are necessary where there is a poor subgrade soil. Four bulldozers excavated the poor subgrade soils. The dimensions of the excavated trench were 0.8 m deep by 10 meter wide and 3.5 kilometers long. The road will have 100 mm aggregate base and 50 mm of asphalt thickness. A bulldozer displaced 115 m \day, at a rate of 100 cedis per day. A laterite soil will be used in the fill operation. The fill operation will need a grader, a vibratory roller and a water truck for 20 days each at a cost of 130 cedis, 138 cedis and 68 cedis respectively. Daily labor rates for this excavation operation is a foreman, 30 cedis, five laborers, 15 cedis each. Truck driver, 21 Cedis and grade checker, 26 Cedis. Daily labor rates for the fill operations are the same as the excavation rates. One forman, ten laborers and a truck driver will be employed for the fill operations. Grading and asphalt laying will require:…
A 7000 meters long and 8 meters wide road is to be constructed in a remote region. Cut and fill are necessary where there is a poor subgrade soil. Four bulldozers excavated the poor subgrade soils. The dimensions of the excavated trench were 0.8 m deep by 10 meter wide and 3.5 kilometers long. The road will have 100 mm aggregate base and 50 mm of asphalt thickness. A bulldozer displaced 115 m3\day, at a rate of 100 cedis per day. A laterite soil will be used in the fill operation. The fill operation will need a grader, a vibratory roller and a water truck for 20 days each at a cost of 130 cedis, 138 cedis and 68 cedis respectively. Daily labor rates for this excavation operation is a foreman, 30 cedis, five laborers, 15 cedis each. Truck driver, 21 Cedis and grade checker, 26 Cedis. Daily labor rates for the fill operations are the same as the excavation rates. One forman, ten laborers and a truck driver will be employed for the fill operations. Grading and asphalt laying will…
Find the quarry productivity per hour for the quarry under the following conditions: • The length of the blade is (2.9) m, the width of the blade is (0.9) m. Clay sandy soil weighing (1601.8) kg / m on the bank scale. soil swelling coefficient (25%) . The transportation distance is (30) meters on flat ground Push-to-go speed is (2.4) km/h. Push back speed (5.6) km/h. The estimated power of the slingshot engine is (72) hp. Actual working minutes per hour Fixed time (0.32) minutes.
A belt conveyor is required to deliver crushed limestone having a bulk density of 75 lb/cu ft at the rate of 200 tons/hr. The conveyor is to be 200 ft between center of pulleys with a rise of 25 ft. The largest lumps are 4 in. and constitute 15% of the total. The conveyor will discharge over the end. For a belt speed of 200 fpm, what is the minimum width of belt that can be used? Calculate the horsepower for the drive motor.
The maximum wheel load that the pavement could carry is 120 kN. If the contact radius of the wheel is assumed to be 250 mm, and subgrade bearing capacity is equivalent to 0.24 Megapascals, calculate the subgrade layer thickness of the flexible pavement in mm using the 45-deg cone pressure distribution method. Use the editor to format your answer