Q) For a Sarda Fall, and using the data given below:• Canal full-supply flowrate, Q = 12 m³ /s• U/S Full-supply level, Ly/s = 50.0 mD/S Full-supply level, Lp/s = 48.8 m%3D• U/S Bed level = 48.4 m• D/S Bed level = 47.2 m• U/S and D/S Bed width = 10.0 m%3D• Side slope = 1 (H): 1 (V)• Assume 1st trial of top width = 0.8 m%3DDetermine the drop in water level, the crest length,the shape and dimensions of the fall section, and itscrest level. Check the assumed value of the top widthand draw the fall section.

Answered: Determine the drop in water level, the…

Determine the drop in water level, the crest length, the shape and dimensions of the fall section, and its crest level. Check the assumed value of the top width and draw the fall section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9. Determine the best hydraulic section for trapezoidal channel that can carry 200 m3 /min.
A rectangular flume is 15 cm wide and 8 cm high. The freeboard is 25% of the flume height. What is the hydraulic radius in cm?
PART III. PROBLEM SOLVING 1. The figure shows a weir, the base of which is 6m below the ground. The necessary flow net has also been drawn assuming K, = K, = K. K = 0.005 m/sec. Compute the following: a. rate of seepage through the foundation in liters/sec. b. uplift pressure at "f. weir uplift force per unit length measured along the axis of the weir. c. 2. For the stressed soil element shown: a. Compute the major principal stress b. Compute the minor principal stress c. Compute the normal stress on plane DE O150 kPa 10 Ty50 LPa
A welded steel channel (Manning n = 0.015) is rectangular in cross-section, being 1.55m wide, and is laid on a slope 1 in 500. Water flows in the channel with a depth of 1.28m, what is the volumetric flow rate?
Please write legibly, complete solutions, avoid rounding off intermediate values, thanks.
Simple solution
An elliptical culvert is 4.5 feet tall and 6.9 feet wide it is filled with water to a depth of 1.05 feet. Find the width of the stream.
Reflection for colored bicycle lanes and intersection treatments: International overview and best practices
A 2-ft-diameter unfinished-concrete drain pipe has been designed to transport 90 ft³/s of water at a depth of 1.5 ft. Part A Determine the required downward slope of the pipe. Express your answer using three significant figures. — ΑΣΦ ↓↑ vec So = Submit Request Answer
The elbow flow passage volume is 0.37 m3 between sections 1 and 2. The flow rate is 0.90 m3/s and the elbow inlet and outlet pressures are 200 kPa and 130 kPa. Consider the elbow weight is negligible. Calculate the horizontal and vertical anchoring forces to hold the elbow in place. my results were Frx = 132.8kPa Fry = 76.7kPa
Civil Q- An irrigation canal has been designed to have R = 2.5 m and S = 1.6 x 104. The sediment on the bed has a median size of 0.30 mm.Determine the amount of bed load using Einstein's method.Assume depth of flow and mean velocity of flow to be 2.8 m and 0.95 m/s, respectively.
1. In the upstream portion of a river, it has a rectangular channel 10m wide and 1.2m deep of water flowing with a mean velocity of 0.75 m/s. Determine the height (head H) in meters of a standard rectangular weir considered without contraction at the downstream portion, if the length of weir is half of the upstream channel width. 2. The river is measured through float method. It has a length marking of 10 meters. Trials were made for 10 times and tabulated the following recorded time in seconds: 12.4 15.5 16.8 17.1 14.9 14.4 16.6 17.2 18.2 15.8 Estimate the flow rate in m3/s of the river if the mean velocity is 75% of the maximum velocity at the top surface. The cross-section area of the channel is close to 15m x 2m.