Determine the distance from the upper surface of the symmetric double-T beam cross section to the location of the centroid. 325 80 -14 Dimensions in millimeters Answer: H = i 215 Save for Later H mm Attempts: 0 of 1 used Submit

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: Q/Draw S and B-M D 8 kuim

A:

Q: 60 10 20 45 35 15 30 2Holes DIA 20 20 60 10 120 30 15

A: Given :-  Orthographic view Draw :- Front view  Top view and Right side view

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: SKN |SkN 4kV/m 15m 1.5

A:

Q: Iron Ore are mainly used to produce high heat in blast furnace Select one: True False CamScanner

A: Iron ore are mainly used to produce high heat in blast furnace.

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: Lycoming TIO-5XX engine is a turbocharged, fuel-injected, horizontally opposed, six-cylinder…

A:

Q: Oil relation between the shear stress and rate of deformation is given in the figure, If the oil…

A: The relation between shear stress and rate of deformation is - τ=μdudyμ=τdudyThe slope of the graph…

Q: Identify Counter-sinking operation from the following drilling operation a. Ob. C. Work stationary O…

A:

Q: dy Solve the differential equation cos(z) dz

A:

Q: Draw the three views and a section elevation:

A: The three views and Sectional Elevation views are drawn with the scale 1:1.

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: Whats the formulae for temperature error %

A:

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: need answer in 15 minute's please 3 (29// A ruck is throw up according to equation s(t) = { +2E-6t…

A:

Q: Calculate the value of fx and fy 240 200N

A: As per given  We have to find fx and fy

Q: Pls provide the sectional view below

A:

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Q// Drow the 5.8.0 and B,m.D yougN

A: The shear force diagram for the beam is

Q: What is the angular velocity (rad/sec) if z-64.77 cm 70 cm Vertical ee Select one a. 101.85 b. 76.39…

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: QUESTION 2 vehicle's tires slip? 25 0.6 m 25 0.6 m 1.4 m Figure 2: A tractor and crate link

A: Given: The weight of the tractor, W = 1.5Mg The coefficient of friction between tyres and ground, f1…

Q: if Re 77 Soo %3D 등 = \ , * 103 Determine f %3D from mod'] chart.

A:

Q: Eind feslads osd Tarque Pressre ond N= mim Ponued 1500xpm

A: Mean effective Pressure is the ratio of work done in a cycle to the engine displacement That is,…

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: If a turbulent water flows inside the piping system, the vertical distance h=30 mm, what is the…

A:

Q: 13- Drawing sheet table contains class item. O True O False 12- The drawing sheet can be used both…

A: 13. in drwaing sheet tables are used to specify each part and its materials to do machining  so the…

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A:

Q: Outline the difference between non associate and associated gas

A: Given Data- Question is given with topic related to gases we have to write difference between…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: Q14 Com Pare between the following 1-blast furnace alld cuPola furnace 2-Said alld Pressure die…

A: Difference between blast and cupola furnace: Blast Furnace Cupola The blast is like an…

Q: I need help answering this.

A: 1)  Only one angular dimension is shown on this print  .i.e., 16002) Two  reference dimensions are…

Q: Use Hra Pe Zoidal Rule with 1, 2.3 and 4 Selment 0.8 when I- S Sex² dx

A: Given: Integration→I=∫00.8e-x2dx Because there are 4 segments which is used to break 0.8 into four…

Q: a) Calculate the thigh, shank and knee angles based on the XY coordinates of the hip, knee and ankle…

A: Given DataCordinatesKnee=1.2,0.5Ankle=0.9,0.1Hip=1.1,0.9

Q: 1. What are the properties of natural gas? 2. Outline the difference between non associate and…

A: (1)

Q: G tg Knowledge Check Answer the following. (a) Find an angle between 0 and 2x that is coterminal…

A:

Q: There are 2 operators working in this process. Calculate the Cycle Time. 6 Days Process 1 0.5 Days…

A: Write the given data. No. of operators, N=2D1=0.5 daysD2=1 dayD3=1 day

Q: The open tank shown, which has a liquid with a specific gravity of S=12.7 as shown in the give…

A: As the fluid is accelerated upwards it will lead to pseudo acceleration(a) acting on the fluid in…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.