Determine the design strength of the beam(properties given below) and the safe service live load if the service dead load is 320 kN.m.Use f'c =22 Mpa and fy=415 MPa. given properties: b=400 mm d'=70 mm d=620 mm As=10-28 mm A's=3-25 mm bars hello please

Q: 7. The horizontal stick of length, L, shown in the figure is uniform and weighs 200 N. Calculate the…

A: Length of the rod = L   Weight of the rod = WL = 200 N   Weight suspended = W = 500 N

Q: Sign 700 mm = 300 mm

A:

Q: A simply supported beam shown below is HEA 400 of 5355 steel. It is laterally supported at points…

A: Since the beam is symmetrically loaded we get Maximum Bending Moment at the Midspan.Maximum bending…

Q: A 1016 mm P 25 mm 330 mm 25 mm 254 mm A 12.5 mm

A: Lets Draw SFD and BMD in terms of P value   M=-P×1.016 kNmV=P kN

Q: 3028 70mm 300mm 500mm

A: b = 300mm d = 430mm f'c = 27.6 MPa fy = 345 MPa

Q: ▷ Example: Determine the allowable service load: in the following. Include beam weight. PD = 2K 6 WL…

A: Since there are two separate problems the first one will be solved. submit the other part as a…

Q: Pkips P/2 kips 10 ft 10 ft to 10 ft 10 ft El = constant Figure 5

A: MFAB=-wl8=-(38)(20)8=-90kipMFBA=+wl8=+90kipMFBC=-wl8=-18(20)8=-45 kipMFCB=+45  kip Restraining…

Q: D = 110 kips L = 280 kips W12 x 87 A992 steel 30

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: Let, P=70KN, a=2.5m, b=1.5m and c=4m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED)…

A: P =70KN L = 9.5m

Q: A W6 x 15 structural steel column is 24 ft tall and is fixed at its base and top. It is braced…

A:

Q: Determine the force acting on members BE, FH, and HK. . Final answer must be rounded to the nearest…

A: Determine the force acting on members BE, FH, and HK.

Q: Determine the type and amount of stress in each member of the truss shown below due to wind load…

A: A truss is an assembly of members such as beams that are connected through nodes and form a rigid…

Q: Determine the force in each member of the truss. State if the members are in tension or compression…

A: Solution: Consider Free Body Diagram of the whole turn: ∑ME=0140×4-FAx×2=0FAX=280…

Q: Hw: Find the slope and deflection in the section CA-A) anel the section CB-B) for the beam Shown.…

A:

Q: Consider the cantilever beam below, which is machined from a steel with an Elastic Modulus of 200…

A: Maximum deflection occurs at free end of beam

Q: - Deteimine th veactions at the supports (pin B Por the beam baded as shown in the figure " .-. 0.2m…

A:

Q: 240 lb 12' 400 lb D 16' A 600 lb 12' F 12' B

A:

Q: lb concentrated forces were applied.

A: Reaction:RA=RB=30014+800+8002=2900lbMax shear = reaction =2900

Q: 3. Check the suitability of the W12x65 section made of A992 steel for the axial loads and moments…

A: Effective length of the column in x-axis buckling = Kx Lx= 1.4*14= 19.6 ft = 235.2 in Effective…

Q: Values An overhanging beam is carrying the following loads: • P= (refer to the table at the last…

A:

Q: Design the steel reinforcement for flexure for the beam to carry the loads shown in the figure…

A:

Q: Design the steel reinforcement for flexure for the rectangular tapered beam to carry the loads shown…

A: Live load, LL = 20 kN/mcover = 75 mmwidth, b = 380 mmHeight at the fixed end, hf = 800 mmHeight at…

Q: Deflection Given: the beam cross-section shown have the following cross-sectional properties  f'c…

A: Gross moment of inertia(Ig)Critical internal moment(Mcr)Maximum service load(Ma)Critical moment of…

Q: Compute and Design the beam loaded as shown. 20 kN/m 10 kN/m 15 kN 5m 4m The im f'c = 20.7 MPa fs =…

A: The total load on the beam can be calculated by adding the distributed loads and the point load. The…

Q: The beam shown has an overall length of L = 5 m and is subjected to the load shown where w = 3 kN/m.…

A: Given : L = 5m w = 3 kN/m Allowable max. shear stress = 13 MPa

Q: The compound bar ABCD has a uniform cross-sectional area of 0.36 in2.Determine the change in length…

A:

Q: REQUIRED: 1. location of horizontal centroid axis.  2. moment of inertia qoth fespext to centroid…

A: Given:S 12 × 50From Table,Area, A=14.6 in2Depth= 12 inThickness of web=0.687 inThickness of…

Q: Problem 6.108 The wood used for the T-beam has an allowable tensile and compressive stress of…

A: Given :

Q: Per missible As in section to ensure tensile Compute the design strength of beam shown if fy = 420…

A: To find : design strength

Q: Result III. A ladder shaped rod ABC is subjected to axial loads as follows, F=10kN₂11-12-400mm,…

A: F=10kN , l1=l2=400mm , A1=100mm2 , A2=50mm2 , E=200GPaTo Find :a) Axial force diagram for the rod.b)…

Q: 3- What size of threaded rod is required for member AB given in figure below. The applied load of X2…

A: Consider the following diagram of the threaded rod. Calculate the angle as follows.…

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A: Find out the forces in member BC and CG in given truss.

Q: Pp= 500 k J P, = 1,000 k I Pp= 500 k // Px=1,000 k fixed fixed Check whether a 17 ft W 14 x 211…

A: Given:- The dead load on the column = PD = 500 k The live load on the column = PL = 1000 k The…

Q: Height h=584.6 mm What is the shear resistance of a universal beam (UB) with the following…

A:

Q: A short prismatic member is subjected to load P = 100kips at corner shown by red dot as shown in…

A: Consider the given figure. (a) The cross-section of the member is symmetric about the y-axis. So,…

Q: Compute the required area of steel, As, For the beam section below. The beam is used to support a…

A: The factored moment is Mu=200 kNm. The width of the beam is b=250 mm. The total depth of the section…

Q: w = 35 kN/m 38-mm diameter 38-mm diameter 50-mm diameter noilos loot orf 100 mm 300 mm 100 mm

A:

Q: For the column shown below, create an interaction diagram on Excel for bending about the strong axis…

A:

Q: Pls help me answer. Thank you.

A: Here's an analysis of the failure mode and the importance of horizontal stirrups in deep beams:Deep…

Q: Step 2: Calculate the area of design steel: • Let's assume the given beam section is a balanced…

A: