Determine the design strength and the allowable strength for the compression member shown. Use NSCP 2015 and a steel with Fy =50ksi. Use theoretical k value. 10 ft W10X60 24 ft 14 ft х-х ахis У-у ахis

Q: Define Dynamic viscosity.

A: DYNAMIC VISCOSITY:   Dynamic viscosity is the properly of fluid to resist the flow. Or to be more…

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: You have decided to build a deck on your new home 12 feet wide x 16 feet long, using the standard 2…

A:

Q: Repiace the loading system acting on the beam by an equivalent resultant force and couple moment at…

A:

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Explain the CORS system.

A: The CORS System stands for Continuously Operating Reference Stations (CORS). It enables…

Q: With the measurements in the following table, calculate the soil moisture flux q (cm/day) between…

A:

Q: kindly resolve or recheck. thank you

A: Given data:

Q: The beam shown in Figure 1 supports a distributed live load of 1.5 kN/m, and a single concentrated…

A: Live load = 1.5 KN/m  Dead Load = 2 KN/m  Single concentrated load = 10 KN  Dimension of beam are…

Q: A Totalstation encompasses: Spirit Level Theodolite EDM

A: Total station encompasses?

Q: The structural diagram. Structure charts may demonstrate module types. Why transform analysis?

A: A structural diagram, also known as a hierarchy chart or structure chart, is a graphical…

Q: Describe the various types of 3D printing technologies, such as Fused Deposition Modeling (FDM) and…

A: Certainly, here's an analysis of two popular 3D printing technologies, Fused Deposition Modeling…

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: What does the design of the project EDGE application create?

A: EDGE refers to excellence in design for greater efficiencies. It helps us in getting more efficient…

Q: The elastic centroidal distance from the bottom is.. * 98 mm 212 mm 200.40 mm 89.50 mm

A: GIVEN DATA DEPTH OF WEB, DW=300 mm WIDTH OF WEB, BW=12 mm DEPTH OF FLANGE, DF=240 mm WIDTH OF…

Q: Which is used as a scale for earthquake intensit Oa) Modified Mrcalli Watt Hertz Richter Ob) Oc) Od)

A:

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: What is Prebid?

A: A prebid is a meeting which generally happens before a bid. It is held to clear up any confusion…

Q: CAD is used to

A: You need to familiarize yourself with a range of civil engineering programme, if you are interested…

Q: Properties of ceramics and classifications.

A: Ceramics are inorganic materials, consisting of metallic and non-metallic elements, which are…

Q: A composite beam is fabricated by bolting two 2.5- in.-wide by 11-in.-deep timber planks to the…

A: Es = 30800 ksi Et = 1660 ksi Determine a. Maximum bending stress in timber and steel if P = 3.5…

Q: Present a problem with solution solving the centroid of a miscellaneous solid.

A:

Q: Based on the graph, what is the best shape to lower the force acting ? Circle or rectangular? Make a…

A: For Circular Shape Column Centre of Gravity (hc) Diagonal Depth Centroid (yc) Diagonal Depth…

Q: lo" A 992 steel 14" -2" what is Mp= ? 14"

A: From the given data calculate all areas find the y bar find the Ix

Q: How to calculate error % in viscosity?

A: Sources of error in capillary viscometer 1. Angular misalignment of the viscometer off the vertical…

Q: How did u calculate minor and major stress

A: Minor and major stress

Q: Step 5 incomprehensiable

A: In the step 5Settlement can be calculated using as below

Q: Design Serviceability Limits

A: Design Serviceability Limits:

Q: How are the redundant determined from the conditions of compatibility?

A: When the number of internal reactions in the structure is more than the number of equilibrium…

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

A:

Q: Q2/ Answer the followings with drawing sketch: A/ briefly explain what is construction joint and…

A: Construction Joint: It is type of concrete joint that is used when a new section of concrete is…

Q: DIFFERENT ACCESSORIES IN THE SHAPER MACHINE WORKS VERTICAL AND HORIZONTA

A:

Q: Section lining or crosshatching is also known as a …?   A. Section pattern B. Hatch pattern C.…

A: Section lining referred as cross-hatching ,is used to indicate material in the sectioned part.

Q: Define the  Modular ratio ?

A: Modulus of elasticity: The ratio of stress and strain is known as The modulus of elasticity. This is…

Q: 20ド Sm 10m

A:

Q: Define Rooof Insulating..

A: Solution; Roof Insulating Insulation helps us to keep the desired temperature in the building. It…

Q: how did e and de derived? show a solution

A: Given: Required: Show the calculation of e and DE

Q: How does a Rube Goldberg machine works?

A: Rube Goldberg was a cartoonist and engineer who was known for making cartoons with complex…

Q: explain how to avoid voids during concrete pouring

A: we have to asked how to avoid voids during concrete pouring

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: When it is said an ERP system is flexible, this refers to which of the following? O The ERP system…

A: We have to determine the correct option

Q: 100 N 100 N 100 100 150 250

A:

Q: Accuracy and Precision for all the following can not determine the accuracy of measurments can not…

A:

Q: Picture Name Uses

A: Name of tool - Wood Rasp Files Use - Used in carpentry for removal of excess material.

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.