Determine the density, weight density, and specific volume at a depth of 8000m from the surface of the ocean where the pressure is found to be 82.5 x103 kN/m2. The density at the surface is 1020 kg/m3 and bulk modulus is 2.4x106 kN/m2 for the given pressure.

Determine the density, weight density, and specific volume at a depth of 8000m from the surface of the ocean where the pressure is found to be 82.5 x103 kN/m2. The density at the surface is 1020 kg/m3 and bulk modulus is 2.4x106 kN/m2 for the given pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In a sample of sand, water seeps at a volume of 158 cm3 in 7.89 minutes. If the seepage area and…

A: Please refer the attached image for complete solution. THANK YOU !

Q: When a soil is submerged, the solid particles are subject to buoyancy caused by the water pressure…

A: Saturated as in context the voids are loaded up with the liquid say water, when we speak regarding…

Q: A cylindrical pressure vessel has an inner diameter of 2 ft and a thickness of in. Determine the…

A: D=2ft =24in t=0.5in

Q: Refer to the figure below: H1 =4 m k = 15x10 cm/sec k2 = 2x10 cm/sec H2 =4 m k = 11x10 cm/sec H3 =4…

Q: The following table contains the estimated bulk mass densities as a function of depth for an…

A: Compaction is the process by which the soil is well distributed and its value is pressed by the…

Q: 2700 kg/m³, po=3000 kg/m?, pm=3300 kg/m³ pw=1000 continental crust. B. If the Musandam has an…

A: Given:- h=5km f=400m D=3700m To find:- H

Q: 1 kg of water has a bulk modulus of 2.4 GPa. Determine the percentage reduction in volume if the…

Q: 1.5 m 0.7 m 1 m A 2 m B Valve (open) Inflow - Sand

Q: An artesian aquifer 25-m thick has a porosity of 17% and bulk modulus of compression 2400 kg/cm².…

A: Given-Kw= 2.14*104 kg/cm2Ks= 2400 kg/cm2b = 25 mn = 17%

Q: Each bulk storage tank shown in the photo has an outer diameter of 4.5 m and a wall thickness of 20…

Q: An artesian aquifer 25-m thick has a porosity of 17% and bulk modulus of compression 2400 kg/ cm².…

Q: B. A soil column is connected to a hanging water column apparatus and allowed to reach equilibrium…

Q: Yw). 3. Derive an expression the buoyant unif weight (yp) in terms of the dry unit weight (Ya), the…

A: To Prove :- Yb = Yd + Yw(n-1) n = porosity of soil e = void ratio of soil Wsat. = Saturated weight…

Q: The water table is located at a depth of 4.0 m below the ground surface in a deposit of sand 16.0 m…

Q: The volume of a reservoir is 2×107 m3, the catchment area is 500 km2, the average annual inflow of…

Q: h=depth %3D p pressure Oe= effective stress %3D p= pgh Example: Estimate pressure and effective…

Q: A core plug has a radius of 0.0125 m and length of 0.05 m. it is completely with brine having a…

Q: EXAMPLE 10.16 Consider a uniformly loaded flexible circular area on the ground surface, as shown in…

Q: The specific weight of saltwater at the surface of the ocean is 10.05 kN/m³. If the Bulk modulus of…

Q: An oil sample weighs 38,612.16 N and has a volume of 4.8 cu.m. Calculate the specific gravity of the…

Q: A large piece of dry rock as a mass of 2450 kg and volume of 0.925 m. The specific gravity of the…

A: Given data : Mass of dry rock (MDry)=2450 kgVolume of dry rock (VDry)=0.925 m3Specific gravity…

Q: What is the specific weight of water at standard condition? If the local gravity is 9.75 mps2, the…

A: Data Available: Standard Condition Local gravity = 9.75 mps2 Asked: Specific weight of water at…

Q: A spherical ball of volume 106mm³ is subjected to a hydrostatic pressure of 90 kN/m². If the bulk…

A: Given- Volume of spherical ball V=106 mm3 Hydrostatic pressure P=90 kN/m2 Bulk modulus K=180 MPa It…

Q: 1.A cylindrical pressure vessel is 500 mm in diameter and has a wall thickness of 22 mm. If it is…

Q: A submarine displaces a volume of 12 370 m3 when submerged just below the surface of the sea where…

Q: the oceanic crust is h=5 km of thickness and the sea average depth is D= 3700 m. (pc=2700 kg/m²,…

A: Given:- D=3700m h=5kM To find:- t

Q: In this model, which layers are confined aquifers?

Q: A spherical gas tank has an inner radius of r = 1.5 m. Part A If it is subjected to an internal…

Q: A dry granite rock weighs 26 N. When it was submerged for 24 hours, its weight increased to 30 N.…

A: Given data- Initial weight of the rock w1=26NFinal weight of the rock w2=30NTo Find-Absorption of…

Q: A barrier island is a large sand body. Consider a barrier island that averages 3 miles wide, 10…

A: given- Barrier island-width B=3 milesLength L=10 milesThickness T=30 feetporosity n=25%

Q: For the condition where the soil is 100 percent saturated and the wet unit weight is known, what is…

Q: Determine (i) density, (ii) weight density, and (iii) specific volume at a depth of 8000m from the…

A: Given: The pressure at the depth of 8000m from the ocean surface and the density at the surface is…

Q: When a pressure of 2×10^4 kN/m² is applied to 50 litres of a liquid, its volume is decreased by 0.5…

A: Pressure = 2 X 104 kN/m2Volume of liquid = 50 litresDecreased volume = 0.5 litre

Q: kN/m². If the bulk modulus for the material is volume of the ball is

Q: ermine the bulk modulus of elasticity of a liquid, if the pressure of the liquid i AN/m². The volume…

A: We knowBulk modulus =Change in pressureVolumetric strain

Q: C. At a depth of 8km in the ocean, the pressure is 83.3MPA. Assume a specific weight at the surface…

A: According to the given details,

Q: A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure…

Q: Calculate the Porosity. Area = 16468 acres

A: Porosity provides information of void spaces in a material. Also known as void fraction.

Q: The volume of a reservoir is 2×107 m3, the catchment area is 500 km2, the average annual inflow of…

Q: When soil water potential in a sandy loam soil goes from -0.1 to -10 bars, the height of an…

A: Given soil water potential in a sandy loam soil goes from - 0.1 to - 10 bars. Height of an…

Q: At a depth of 7km in the ocean the pressure is 957 MPA. Assume a specific weight at the surface of…

Q: The water table is located at a depth of 4.0 m below the ground surface in a deposit of sand 16.0 m…

Concept explainers

Pressure and Stress

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A SATURATED SOIL HAS VOID RATIO EQUAL TO 0.65 AND sg = 2.9. WHAT IS THE SUBMERGED UNIT WEIGHT OF THE SOIL? * Your answer
3. Determine the bulk modulus of elasticity of a liquid, if the pressure of the liquid is increased from 7 MN/m² to 13 MN/m². The volume of liquid decreases by 0.15%. A. 4 kN/m² B. 40 MN/m² C. 7.06 N/m² D. 4 GN/m²
Given a suspension in water of uniformly sized sphere (diameter = 6,102.36 μin, density = 71.17 lb/ft3 hasa solids concentration of 25% by volume. The suspension settles to a bed of solids concentration of 55%by volume. The rate at which the sediment/suspension interface rises, in mm/s. Assume waterproperties: density, 1000 kg/m3; viscosity, 0.001 Pa.s a. -0,.401 b. -0.328 c. -0.375 d. -0.450 e. -0.833
At a depth of 14 km in the ocean, the pressure is 71.9 MPa. Assume a specific weight at the surface of 10.1 kN/m3 and an average bulk modulus of elasticity of 2.81 GPa for that pressure range. Compute the change in specific volume in mm3/kg between the surface and 14 km depth. Round your answer to 2 decimal places.
A large piece of dry rock has a mass of 2,350 kg. and a volume of 0.925 m. The specific gravity of the rock mineral is 2.70. Determine the porosity of the rock.
One of the methods in measuring bulk volume for porosity measurement is direct calculation. By using the below data, determine the porosity for this core. Table 1: Parameters of rock-fluid Parameter Value, unit Core diameter 1.57 inch Core length 3 cm Dried core weight 100 g Saturated-brine core weight 110 g Brine density 1.30 g/cm³
I need the answer as soon as possible
PROBLEM 3. If a pressure applied to 1 kg of water is 13.2 x 10^7 N/m^2 5 points causes a percentage reduction in volume is 6%, determine the Bulk modulus. Express your answer in the appropriate Sl unit. * Your answer
Situation 1: The mass of glycerin is 500 kg with a total volume of 0.315 m³. 1. Compute the unit weight in kN/m³. (a) 17.232 (b) 15.571 (c) 18.621 (d) 14.213 2. Compute the dry density in kg/m³. (b) 1762.40 (a) 1945.23 (c) 1742.30 (d) 1587.30 3. Compute the total weight in kN. (a) 3.451 (b) 4.905 (c) 5.124 (d) 6.012 A
Figure Q.3 shows a liquid reservoir that is density stratified. The top layer has thickness b and uni- form density pt. The middle layer has thickness d and a linearly varying density given by Pt (") (h - b) Pb - Pt P(h) = Pt+ d p(h) for (b Pt. Figure Q.3. Use the information provided above and in Figure Q.3 to derive the gauge pressure distribution for the liquid in the reservoir.
A tank 12 m high is to be filled with oil with unit weight of 9.4 kN/m³ as shown in the figure. Neglect the weight of the tank. 12 m GWT 3 m Sand: y = 18.88 kN/m³ Clay: y = 17.31 kN/m³ e = 1.27 LI = 0.645 14 m PL = 20% MC = 40% Calculate the compression index of the clay layer. O 0.369 O 0.346 O 0.421 O 0.325
When a pressure of 2×10^4 kN/m² is applied to 50 litres of a liquid, its volume is decreased by 0.5 litre. The bulk modulus of liquid in N/m² is