Determine the deflection at the free end of the cantilever beam. E = 250 GPa and I = 420 x 106 mm4 shown in figure 5. 75 kN a. 373.371 mm (downward) b. 0.373 mm (downward) 37.337 mm (downward) d. 3.733 mm (downward) C. AF -6 m B -6 m Figure 5 C 25 kN/m -6 m D

Determine the deflection at the free end of the cantilever beam. E = 250 GPa and I = 420 x 106 mm4 shown in figure 5. 75 kN a. 373.371 mm (downward) b. 0.373 mm (downward) 37.337 mm (downward) d. 3.733 mm (downward) C. AF -6 m B -6 m Figure 5 C 25 kN/m -6 m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Sketch thefollowing figure ,orthographic view ( using catia ) Metion the top view side view and…

A: From figure.......

Q: 1/2x10ft

A: We are given: 1/2×10 ft The given expression is equivalent to computing half the length of 10 f.

Q: Draw top, front and right view of the following isometric views

A: Top view

Q: owing 'shapes', determine the follow , A tion of centroid; xeft, rightYbot roidal Moment of Inertia;…

Q: 0+365 0+370 0+375 0+380 BM2 1.008 0.953 0.880 0.800 0.783 COMPUTATIONS: 1. Computing Height of…

A: The formulas to be used are given in question

Q: Show the quadrants of a circle and within the circle show S 30° W

Q: Draw the shear force and bending moment diagrams and sketch the qualitative deflected shape.

A: The figure given in the question are as follows: w=1.5 klf

Q: What is the interior angle of CP#1? Answer in the format ddd-mm-ss without any Instrument is @ CP#1…

A: If BS is CP#6 and, FS is CP#2 And angle is taken from right then this angle must be exterior angle…

Q: Q1. Draw the plan and components of the given line diagram. Assume necessary any suitable data. W,…

Q: Show Isometric View.

A: Answer We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: Assignment 2.: A line CD, 60mm long, is perpendicular to VP and parallel to HP. It is 20 mm above…

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: Draw the plan and elevation of the given line diagram. W W.C V KITCHEN D, 2100×1200 3600x2800 BATH V…

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

Q: 02. Draw a neat sketch (closed traverse) for this note book entry. D 55 40 C24 24 30E B22 10 A

A: Given:- The notebook entry is given To determine:- Draw a neat sketch for the closed traverse

Q: L (Isometric Drawing) J 56 104

Q: Exercise 1.10: Draw the Isometric view from the provided views (Front, Top, Right). Note: Third…

A: Isometric view from the given orthographic projection.

Q: What is tangent modulus?

A: The tangent modulus can be defined as it is the slope of a line tangent to the stress-strain curve…

Q: 5 TOP 10 8 FRONT ? Isometric View RSV

Q: Find the areal scale for the following 3cm+09km

A: Given: Map distancex=3 cm Ground distanceX=9 km To find: Areal scale

Q: Draw the the 3 principal views and auxiliary view (like in the second photo)

A: Auxillary view: The orthographic view drawn taken according to the line of sight which is not…

Q: 60 mm 30 mm 30 mm 45 mm

Q: Q2: Draw front and side view projection for the following 36 12, 34

A: Given section: If you look at the given section from the front, the red coloured area will be…

Q: B Look to the Contour map above Solid line is the ground surface level Dashed line is Water table…

A: Contour lines are drawn on contour maps which represents the elevation or depression at any…

Q: A wall has an area of 75 sq ft. Find to the nearer hundredth square meter thearea of the wall.

A: Given:- area = 75 sq ft To find:- Nearer hundredth square meter thearea of the wall.

Q: weétermine the yalue j = 2. Det ermine the Yalue & I with Respecd to centroidal X axis =

A: 1. Value of y¯ Let 1 & 2 be the rectangle and 3 & 4 be the triangle.y¯=∑ay∑a…

Q: ftware Orcad cadence in detail?

A: A schematic editor (Capture), an analog/mixed-signal circuit simulator (PSpice), and a PCB board…

Q: A blueprint for the floor of a natural history museum is shown the scale of the museum to the…

A: Given- A blueprint for the floor of a natural history museum. scale used=20 yards to 1 inch…

Q: g1= Station 18+26 18+00 17+00 16+00 15+68 g2= X 0 Elevation of BVC = gix 82-81x2 2L Elevation 899.02

A: Vertical Curve : Vertical curves, which may or may not be symmetrical, are supplied to alter the…

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: Q1. DRAW THE ORTHOGRAPHIC PROJECTION VIEW OF GIVEN OBJECT BELOW. ELEVATION PLAN SIDE VIEW

A: Instructions : To draw the orthographic projection view ( First angle method ) consider the…

Q: Isometric drawing

Q: Determine the centroid of the lines that form the boundary of the shaded area shown. Determine:…

Question

sit 11

Determine the deflection at the free end of the cantilever beam. E = 250 GPa and I = 420 x 106 mm4 shown
in figure 5.
75 kN
a. 373.371 mm (downward)
b. 0.373 mm (downward)
37.337 mm (downward)
d. 3.733 mm (downward)
C.
A
-6 m
B
-6 m-
Figure 5
C
25 kN/m
-6 m-
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The vernier scale reading (in cm) is a 0.045 b. 0.9 C. 0.45 d. 0.09
Draw the missing view. exact scaling not needed
42 12 18 48 70 The known: front projection, side projection Required: Draw the three projections 32
PLEASE ANSWER, IT WILL HELP ME BIG TIME! THANK YOU!
What is the elevation at point A, C, and E?
Q1. Draw the plan and components of the given line diagram. Assume necessary any suitable data. W, Bed W, 4 x 3.0 m 4 x 4 m D, W D, Hall D V 2x2 m 2 x 2 m D, 4 x 6 m Kitchen D, Wi 4x 3 m W. D, W D-1000 x 2000 mm, D, - 900 x 2000 mm, W - 900 x 1200 mm, W,- 2000 x 1000 mm, V- 800 x 300 mm. nswer:
Hand written and clean writing please
Draw the plan and elevation of the given line diagram. W W.C V D,+2100x1200 KITCHEN 3600x2800 BATH W D D2+ 2100x1500 D, DINING W, BED 4800x2150 W 3500 x4000 LIVING -3500x4000 W, D, Reference D-1000x2000 D BED 4800x4300 W VERANDA 3500x1550 D-900x2000 D2 -800x1800 W-1000x1000 W-2000 1000 V- 800x500 W,
A thin circular rod is supported in a vertical plane by a bracket at A. Attached to the bracket and loosely wound around the rod is a spring (spring constant K = 3lb/ft) and unreformed length equal to the arc AB. An 8-oz collar C that is not attached to the spring can slide without friction along the circular rod. Collar is released from rest when teta = 30 degrees. What is the maximum height above point B reached by the collar? (Non-anonymous question O)