Answered: Determine the dc resistance levels for…

Determine the dc resistance levels for the diode a. I₁ = 2mA (low level) b. ID=20mA (high level) c. V₁ = -10V (reverse-biased) -10 V 30 200 10 29 ID(mA) 0 1 μA 0.5 0.8 Silicon VD (V)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: Determine the dc resistance levels for the diode of the figure at: ID = 2 mA ID = 20 mA VD = -10 V…

Q: Find the current I if both diodes are identical. Voltage V = 0.8V and let the reverse saturation…

Q: (a)

A: In the given circuit diagram, Given value of cutting voltage in forward-bias region is 0.6 V As we…

Q: The rate of fall of current in a diode with reverse recovery charge and reverse recovery current of…

A: Given : reverse recovery charge of diode and reverse recovery current of diode To find rate of fall…

Q: Determine the minimum value of RL to ensure that the diode is “on

A: In this question we will find value of RL..

Q: For a silicon diode, the value of the forward-bias voltage typically (a) must be greater than 0.3 V…

A: For an ideal diode, when a diode is forward biased, then the diode starts to conduct a significant…

Q: Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across…

A: as we can see R1 and R2 are in parallel so, Req1=1R1+1R2Req1=19kΩ+118kΩReq1=6 kΩ R3 and R4 are in…

Q: Si Ge Io2 R1 R2=1KQ Si R3=2KN Ir2

A: In the given circuit current ID1 and ID2 is flowingGiven in the circuit vaules for Si =…

Q: For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy,…

Q: In a power diode the rate of change of reverse current is 30 A/µsec and charge involved in reverse…

A: Given, Rate of change of reverse current, didt=30 Aμsec. Charge involve in reverse recovery, QR=11…

Q: 120 V rms a. b. 3:1 00000 reliee 叶 DI D₂ # What is the peak current through each diode? What is the…

Q: Determine the power dissipated by the diode

A: In this question we will find power dissipated by diode....

Q: In the Figure as shown below the current (I) will be equal to: Assume that all diodes are silicon…

A: Fig: Given circuit replace the diode with 0.7V battery By symmetry…

Q: For a silicon diode, calculate the current at room temperature if the forward voltage is 0.5v and…

Q: Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the…

A: Given data : simplified model for the diode,

Q: All diodes are si 0.7. For the range -2<Vi<6V, find the output voltage v0 in terms of voltage v1.

A: Given: A circuit with the range of input voltage -2<Vi<6 V. Both the diodes are of silicon…

Q: In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c.…

A: The solution can be achieved as follows.

Q: What would cause the barrier potential of a silicon diode to decrease from 0.7 V to0.6 V?

A: The potential barrier in a very tangent junction might be a kind of barrier that prevents…

Q: For the given circuit, assume the diode D1 and D2 are the ideal diodes. The average value of the…

Q: Draw the corresponding output waveform of the double diode partial limiter below using simplified…

A: In this question We need to draw the corresponding output waveform. We know forward bias voltage…

Q: (+) 0.25 V_SIN RL -1 V_SQR 0.75

A: To solve above give problem concept required are: A diode is turn on when forward voltage is applied…

Q: normal diode uses 0.7V model, and zener diode has 4.7V breakdown voltage. how can i get a waveform…

A: In this question, We need to draw the output voltage waveform If diode uses 0.7V model, and zener…

Q: Determine the transition voltage (VT) that will cause a variation in state for the diode. 8 V 10…

A: We need to find out transition voltage for given circuit.

Q: If Vs is 0.5 sin wt V and the diode is a silicon diode, determine the current I for the given…

Q: Find the Q-point for the diode in the following circuit using a) The ideal diode model; b) The…

Q: Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across…

A: When a voltage is applied across circuit., Diode D2 & D3 Become Short -Circuited and Diode D1…

Q: Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state…

Q: Calculate the threshold voltage of a silicon diode at a temperature of 0°C if at 25°C. it has a…

A: Given, The threshold voltage of silicon diode at 25°C is 0.7 volts.

Q: A germanium dio de has a current reaches 80% of its saturation point at 115°C. Calculate the voltage…

Q: Given the following circuit with VDD = 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for…

A: For given circuit, it is asked to find the current

Q: D3 120 V RL 10 kn D4 alle elll

A: Diode current will be decreased as it depends on the load current.

Q: What will be the value of the reverse saturation current for a Si diode operating in forward bias…

A: Using Shockley’s equation, the value of the current flowing through a p-n junction diode can be…

Q: Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across…

A: Assuming ideal diodes means that in the forward biased condition, the voltage across the diodes will…

Q: Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across…

A: It is given that the given diodes are ideal ones. so we can say that if the diodes are forward…

Concept explainers

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.

Question

Determine the dc resistance
levels for the diode
a. I₁ = 2mA (low level)
b. ID=20mA (high level)
c. V₁ = -10V (reverse-biased)
-10 V
30
200
10
29
ID(mA)
0
1 μA
0.5
0.8
Silicon
VD (V)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
For the diodes used , at what Voltage (VD) does condection stars .
If one of the diodes in the figure below is open, the average voltage across the load is:(a) increases (b) decreases (c) does not change
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw output waveform for the following circuit. Suppose input is a pure square wave with a positive half at 10 V and negative half at -10 V for ideal diodes. D1 D2 220 R3 R1 1k R2 1k
A silicon diode is used in the positive clipper of the figure below. Explain and sketch the output wave shape if the input is a) A sine wave with a peak value of 5V. b) A square wave with a peak value of 5V.
PLEASE ANSWER THIS MCQ
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
find the diode voltage and diode current on each figure.