Determine the components of the pin reactions in the pins at A, B and Cusing the Method of Members. Enter your answers to one decimal place. F - 35 kN F2- 75 kN 1 0m 3 0m 4Om

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: Quiz #1 Problem 1: Prove the following relationship. Gs Yw (1+ Mc) W 1+e

A:

Q: QUESTION 5 Which of the following represents the location of the horizontal plastic neutral axis (X,…

A: Solution Find the location of horizontal plastic neutral axis

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: Find the centroid for the shaded area

A: Given Diagram with dimensions    To find  Centroid of the shaded area

Q: Name this force system Question 18 options: Non-planar concurrent…

A: To name the force system.   Coplanar force system, is one in which all the forces lie in the same…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 0.5 in. 4 in. |0.5 in. -3 in.-

A:

Q: Determine the polar moment of inertia with respect to the centroidal X and Y axes. Present detailed…

A: Given: Required: Polar moment of inertia about centroidal x and y axes

Q: Why Nc=9 and Nq=1

A: Given question is based on static method of analysis bearing capacity of pile.

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: is required to find soil pressure at a depth of 10 ft beneath the interior corner A and exterior…

A:

Q: Q2- Find the centroid for the shaded area shown in the figure. (All dimensions in mm) 20 40 20 50

A:

Q: Matching Type: Match the real beam to the corresponding conjugate beam 1. 2. 3. 5. & 6. 7. 8. a. b.…

A: Objective: To match the given beams to the given conjugate beams.   The transformation of supports…

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: 6Ocm 20 29 cm

A:

Q: Q5: : In your own words, compare the following images, using a table.. dream dreamtime dreamsme dre…

A:

Q: 80 mm -L- В D 60 mm

A:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 I 30 - x 100…

A:

Q: CORRECT ANSWER

A:

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: (1) a L₁ B P b C L2 C D

A:

Q: 200N 30 R, "y at point C

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: 1. Ah = [ Select ] 2. Av [ Select ] 3. MA = [ Select ] %3D 4. C, = [Select ] 5. Dy = [ [ Select ] 50…

A:

Q: Q4: Convert the following into required: 1- An area 4.2 cm on amap with scale 1/5000 > Don , Olk,…

A:

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: What is the distance between the kerns for the section given below? K- 100- 50 200 50 50

A:

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: Total number of bags needed if each bag is 50kg (110lbs) and total weight of aggregates and water…

A:

Q: Draw and label theV and M 15KN diagrams. Fill in the blanks. Find M- max and the equations for q. V,…

A: The beam is an important element in the construction of any structure or building. It resists…

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.