Determine the combined moment made by the two pairs of forces about point O and about point C. 3.2 KN |-2.7 m² B 8.9 KN C 4.1 m 4.1 m 2.7 m 6.0 m 8.9 KN 2.7 m ΤΑ -3.2 KN

Q: y

A:

Q: Q243 For the force system shown in figure C24); determine The magnitude and location of the…

A:

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: The hollow cylinder shown in Fig. P.14.22 is built-in at one end and carries a vertical load of 2 kN…

A: The bending moment due to force is - M=2×1 kNm=2000×1000 NmThe twisting moment due to force is -…

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: Q: A block is 45 mm long, 20 mm high, 10 mm thickness. the block is subjected to a uniformly…

A:

Q: 2. EVALUATE dx e

A: The indefinite integration is represented by ∫f(x)dx and the solution is F(x)+C, where F(x) is…

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: 1) Resolve the force F into components along the a and b axe agnitudes of these components. (Use:…

A: given:

Q: find Q ? L 7om dsolm Lsioum L. 2om f=0002

A: Velocity of flow at entry of 100 m pipe, v=2gh where, h=height of reservoir=8m Therefore velocity,…

Q: The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as…

A:

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: Determine all furce mem bers of truss Shown the

A:

Q: H G 60 E D 7 kN 7 kN 9 kN 6m 6m 6m 6m

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: 15 kN 20 kN 2 m m

A:

Q: F 1000 lb y 500 lb 45° 30°

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: determine (a) the required value of a if the wn is to be vertical, (b) the corresponding 30° 200 N

A:

Q: Q2/ As shown in fig.(2). Prove the main equation for the coefficient of frictional force between the…

A:

Q: 2.5". 45 45°

A: Let’s divide the shaded area into two sections. Section 1 is a circular arc OCD and section 2 is a…

Q: What is the resultant force?

A: Let us consider that an object has two forces acts on it. These forces are  10 N to its right.  50…

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

A:

Q: Horizontal Component of the force at B: Vertical Component of the force at B: Horizontal Component…

A:

Q: x If 0 = 50°, and the magnitude of FA is 8 kN, and the magnitude of FB is 4 kN, determine FRx and…

A:

Q: Fint total force acting on point A. Point A can be anywhere.

A:

Q: Find (Ix&ly), if a=30mm. a

A:

Q: A) Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A:

Q: The design specifications for the steel shaft AB require that the shaft acquire a strain energy of…

A:

Q: data - The gas operating in the cycle is air. - The circulating air flow is 1 kg/s - The pressure…

A: Given data is

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.