Determine the angle 0 made between the axes OA of the flag pole and AC cable, given x=2 6m 1.5 m 2m Fa=55 N 4 m. F = 40 N x m

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: dy = m y2 dx

A:

Q: i cant read this.. can you write it out??

A:

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: Determine ly and ky.

A:

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: 200 mm В

A:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Find this range. Ds i mm

A:

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: R D.

A:

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.